Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by keens

  1. keens

    Weldolet or Sockolet

    How do you design or model a weldolet or sockolet in COMPRESS?
  2. keens

    PWHT & Impact Testing

    metengr, It is SA-537 Class 2. Thanks...
  3. keens

    Condensate storage tank material suggestions

    I agree with kenmac777. We specialize in API Storage Tanks, and we typically design condensate tanks with A36 w/ internal lining. The lining is usually epoxy coating.
  4. keens

    PWHT & Impact Testing

    Gentlemen, We are looking into building a vessel 28 feet in diameter x 308 feet tall out of SA-537 Gr.2 material 1 ¼” thick. The design temperature is -50°F so the material will require impact testing. Will heat treating be required by the ASME Code? Thanks...
  5. keens

    Temperature Ranges for Flange Material

    Hello All, My company is currently fabricating three LNG Tanks, and the temperature can reach -265 Deg. F. I am in the process of trying to purchase some 4" and 6" 150# Flanges that would be good for this temperature. Some of the Flanges will need to be Stainless Steel, and some are...
  6. keens

    Reinforcing Pads Vs. Design Temperature

    Gentlemen, Does anyone know wherein Section VIII, Div. 1, it recommends not using Repads above 800 degrees F? Thanks...
  7. keens

    Temperature Ranges for Bolt Materials

    Thanks... As always, you are very helpful. I will and try to return the favor someday.
  8. keens

    Temperature Ranges for Bolt Materials

    Thanks metengr, I thought that was were I should be looking, thanks for putting me on the correct path. My only problem with using ASME Section II, Part D, Table 3, is that it does not give you the lowest temperature that the material can be used, it only starts at -20 Deg. F. I know...
  9. keens

    Temperature Ranges for Bolt Materials

    Gentlemen, Does anyone know wher to find or have information on the Temperature Ranges for Bolt and Nut Material? Thanks...
  10. keens

    ASME BPVC Section VIII, Div I, 2004 Edition w/ A06 Addenda

    Gentlemen, Does anyone know if a 2006 Addenda has been issued for ASME BPVC Section VIII, Divsion I, 2004 Edition? And if so, where can I find a copy? Thanks... Also, if I have a shop that is getting a vessel U-Stamped to the 2006 Addenda, but the COMPRESS calcs do not have the 2006...
  11. keens

    ASME Heads

    Gentlemen, Does anyone know of or have a design standard they use when deciding whether to use a 2:1 Elliptical Head or an F&D Head in their design? I know 2:1 Elliptical Heads are usually used for small and medium diameters, and higher pressures. And F&D Heads are usually used for lower...
  12. keens

    2:1 Elliptical Heads Vs. F&D Heads

    Gentlemen, Does anyone know of or have a design standard they use when deciding whether to use a 2:1 Elliptical Head or an F&D Head in their design? I know 2:1 Elliptical Heads are usually used for small and medium diameters, and higher pressures. And F&D Heads are usually used for lower...
  13. keens

    Defeciences/Warnings in COMPRESS

    Hello All, I am in the process of designing a Sour Water Stripper that is 6'-0'' I.D X 95'-0'' T/T, and all the nozzles have external loads. I have a few questions regarding the Warnings/Defeciences Report, if anyone has experienced the same issues. 1. For one of my Nozzles located in...
  14. keens

    Thin-Out of ASME Heads

    Hello All, During the forming process of ASME Heads, where does the most Thin-out occur? Or what area of the Head will see the highest stresses? Thanks....
  15. keens

    Nozzle Loadings

    Hello All, Does anyone know if it is a good practice to include Nozzle Loadings for Flange Ratings? What I mean is, in COMPRESS there is a check you can perform that will include external nozzle loadings in the Flange Rating. Or it will also use the Nozzle Loadings to limit the MAWP...
See more

Part and Inventory Search

Back
Top