Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by jproj

  1. jproj

    Forged Flange Modification

    Hi All, I have a question relating to a 900# RFLWN "Type V2" FVC forged flange (SA-182 F22 CL3 material) that is currently on a vessel in hydrogen & sour service (similar to the one pictured on page 11 here: http://www.forgedvesselconn.com/catalog030199_2.pdf ). Is it possible (perhaps...
  2. jproj

    Simplify table w/out hide or group

    Hi Morten, I would specify the order desired - similar to how pivot tables work. I really am just looking to summarize information contained in a very large and detailed spreadsheet into a "management friendly" format. I know how to do this with a macro, but would prefer to work in the...
  3. jproj

    Simplify table w/out hide or group

    Hi all, I have a large group of data basically organized by columns that I want to consolodate into a much smaller table on a separate worksheet. The smaller table would contain the same information as the larger table with the same format, but would exclude many unnecessary columns. I would...
  4. jproj

    Pressure Rating for Dual Cert. Flange (304/304L)?

    Thanks to everyone for their input. Just for furhter clarification - the application is process piping designed to ASME B31.3 (attached to a section 8, div. 1 vessel). L-grade piping and flange materials are required for corrosion resistance to the process fluid. There are a few instruments...
  5. jproj

    Pressure Rating for Dual Cert. Flange (304/304L)?

    I'm hoping someone can verify my understanding of the pressure ratings of dual rated flanges ASME B16.5. I only have the 1996 ed. so bear with me on the paragraph numbers. My understanding is that either of the applicable flange rating charts may be used (per paragraph 2.7 and 4.1.2(d)) as...
  6. jproj

    UG-29 Clarifications

    SnTMan, After a few more calculations, I have concluded that the tabular values are not typos, but are approximately equal to the result obtained from the formula B = 2A/E (as described in Setp 5 when B is below the values given on the figure). Thanks for the clarifications.
  7. jproj

    UG-29 Clarifications

    I am trying to work through UG-29(a) and have a couple of questions. 1) Assuming the vessel has multiple stiffening rings, are I and I' the moments of inertia for a single stiffening ring, or the sum of all stiffening ring inertias? 2) Similar to the above question, is As the total cross...
  8. jproj

    Application of Seismic Loads to Saddle

    The vessel is certainly large (13' OD x 141' T-T), but IMO 5 saddles are unnecessary. It was a customer requirement and likely specified in order to reduce the structural steal per beam load. As far as the dead weight, I have already estimated the distribution (based on assuming the vessel...
  9. jproj

    Application of Seismic Loads to Saddle

    I am trying to apply a horizontal seismic / wind load to my vessel supports (vertical reaction load). Unfortunately, the only reference I have available is the Pressure Vessel Design Manual by Dennis Moss. Aside from the errors and non-existent derivation of equations, the outlined equation...
  10. jproj

    Table UW-12 / Head Circ. Seam JE Clarification

    EJL, UW-12(d) would apply for seamless shell sections would it not (JE = 0.85 for no RT)? (d) Seamless vessel sections or heads shall be considered equivalent to welded parts of the same geometry in which all Category A welds are Type No. 1. For calculations involving circumferential stress...
  11. jproj

    Table UW-12 / Head Circ. Seam JE Clarification

    I have another question regarding the joint efficiency of circumferential seams between shell sections (not seamless) when radiography is not performed. Since UW-11(a)(5) does not apply, is it accurate to say that the circ. seam between two shell sections (not seamless) is per Table UW-12(c)...
  12. jproj

    Table UW-12 / Head Circ. Seam JE Clarification

    Thanks for the clarification and sorry for the typo in my first sentence (JE = 1 with spot RT & 0.85 without spot for seamless heads). I think I understand it now. Thanks again! jproj
  13. jproj

    Table UW-12 / Head Circ. Seam JE Clarification

    UW-12(d) clearly specifies the joint efficiency for seamless heads with or without spot radiography (0.85). Does the code specify JE for seamed (e.g. two-piece) heads? It is my understanding that it depends on the RT performed on the head long seam(s). For instance, if the 2-piece head long...
  14. jproj

    MAWP vs. Design Pressure

    G. García, I'm not sure how familiar you are with vessel design calculations, but The design pressure (minimum and maximum) must be initially used along with the design temperature (minimum and maximum) to determine the minimum thicknesses required. As we all know, calculated values are not...
  15. jproj

    MAWP vs. Design Pressure

    That's pretty much what I expected (basic logic the way I look at it... 2+2=Y is the same as Y-2=2). What still confuses me is why an AI would insist on new calc's using the MAWP as the DP when the current calc's (with the actual DP) already show the MAWP. Is this just an incompetent AI or...
See more

Part and Inventory Search

Back
Top