Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations JAE on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by Javiduc

  1. Javiduc

    NX Reference Sets - Again

    Another approach would be to use promote body. You design de uncrimpped body at part level (part A), then you assemble with the wires and you have an assembly with all the parts but not crimped yet (assembly B), then you create another assembly (assembly C) and add the assembly B inside assembly...
  2. Javiduc

    Energy Chains

    Yes, I meant assembly constraints and I meant constraint the link components to the sketch curves but not each sketch curve but all at the same time, that was the reason I unite the sketch. Because when I edit the sketch some links that were constrained to a line need to change and be...
  3. Javiduc

    Energy Chains

    I have tried to methods. The first one was drawing a sketch with the path of the chain, unite the curves of the sketch, insert links as components and restrict the components to the united curve. It did work well for slight path modifications but if the modifications were big the assembly...
  4. Javiduc

    NX10 promote body

    Hello cowski, With hole series I can't make a threaded hole to different bodies, I mean with threads in different bodies. I need to create threaded and not threaded holes through different components (all different components have to have threads if the hole is threaded or not threads if the...
  5. Javiduc

    NX10 promote body

    Hello Xwheelguy, thank you for your advise. Yes, I will probably place an ER for promote body (and for other improvements too), It will take me some weeks though. I have been learning NX for a few months and we have recently started to use it in the company, we had a "trial" period and now we...
  6. Javiduc

    NX10 promote body

    I totally agree. Promote body is a great command, much better than wavelinking, but needs some improvements. Not as useful as relink, but I think it would be good if the command let users to define in just one step that all components of an assembly should be promoted and united and even...
  7. Javiduc

    Control what happens after you Close a single part file

    I came from Solidedge and for me is strange to have so many "Windows" opened with different parts, a bit confusing when doing ctrl+tab and I sometimes have problems with some workflows, for example when I open a drafting (master model approach) then set the geometry part as displayed part, when...
  8. Javiduc

    Export pdf file

    Yes, I use export PDF. By "thats the way I am doing it now" I meant the same process but in the export PDF command. Anyway thank you for the advice and info.
  9. Javiduc

    NX10 promote body

    Hello John, thanks for the info. If promote architecture had improvements, then I guess that the information I got about this command going to be erased is not correct.
  10. Javiduc

    Export pdf file

    Hello Yevgeny, Yes, that is the way I am doing it now. I know it is not difficult to do, but it would be very handy if you can select all sheets by default (saving clicks and avoiding mistakes). In others softwares it can be done that way.
  11. Javiduc

    NX10 promote body

    Hello Eric, I also use promote body for machined parts and I have been told that this command may be deleted from future NX releases which scared me a lot because others ways to represent machined assemblies are worst thant promote body. I think promote body is a bit buggy command. For...
  12. Javiduc

    Export pdf file

    Yes, all sheets un the same file. It is easy to do by selecting them manually but i would like to set this Commander to select all sheets by default avoiding some clicks and posible mistakes
  13. Javiduc

    Export pdf file

    I like to use this command to print my PDF files because for me it is quicker than use an external PDF printer. But I would like to set by default to print all sheets instead of select them manually. Is that posible?
  14. Javiduc

    Deleting all disconected anotations in drawing

    Thank you phillpd! that is exactly what I was looking for :) Is any way to add that button to a customized tab?
  15. Javiduc

    Deleting all disconected anotations in drawing

    When I delete some features in a 3D part like hole features containing several holes and update views in drafting, then the dimensions,axis... became disconnected and I manually select and delete them. In Solidedge, I have the option to delete them all with just one button. Is there any way to...
See more

Part and Inventory Search

Back
Top