Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by jacphi

  1. jacphi

    Power XFMR Testing

    hi buzzp, yes the failed samples were taken first. but no oil was bleeded out. yes even we feel that it might have failed due to air. regards,
  2. jacphi

    Power XFMR Testing

    thanks jnims, now i understand why the inspector did not accept the test.by the way our test booth does not have the facility to apply 100% rated current. is there any alternate method you can sugest??? or else we are doooomed......
  3. jacphi

    Power XFMR Testing

    thanks jnims, does that mean that for measuring load loss, rated current is to be applied and for winding temp rise test not below 85% is to be applied? is my intrepretation of the ansi std correct??? regards,
  4. jacphi

    Space heater for outdoor control cabinet

    hi all, The local specification for outdoor control cabinet states that "The interiors of unventilated metal cabinets (exclusive of internal heat-producing sources) can reach 56°C. The components and its accessories, including cabinets and junction boxes, shall be designed accordingly" The...
  5. jacphi

    Power XFMR Testing

    hi jnims, as mentioned in C57.12.90-1999, Clause 11.5.2.1 When test equipment limitations dictate, operating at a value lower than rated current, but not less than 85% of rated current, is permissible. does this applies for load loss measurement also or only for winding temperature rise...
  6. jacphi

    Power XFMR Testing

    Hi all, i was involved with testing of a 7.5 MVA, 13.8kV-4.16kV transformer. the following points were noted. 1,The Liquid-Temp Indicator (thermometer)installed was with capillary and not direct stem type. Does ANSI C57.12.10 states that the Liquid-Temp Indicator (thermometer) shall be direct...
  7. jacphi

    Symmetrical/Asymmetrical short circuit current

    We have a requirement for the 480V switchears and Motor control centres to have rating for 65kA (symmetrical) short circuit current and the main bus bracing for 100kA momentary short circuit current (Asymmetrical). I would like to know if the vendor provided 65kA (symmetrical) short circuit...
  8. jacphi

    electric supply to fire water pump

    some continuous some intermittant..there are 5 different feeders on this MCC.
  9. jacphi

    electric supply to fire water pump

    controlgear is a term used for motor control centres(MCC).
  10. jacphi

    electric supply to fire water pump

    with all the sugestions posted i am convinced that the feeder breaker to the fire pump should be rated for 1500A with short circuit and groung fault protection. the only doubt still remaining is the rating of the controlgear,1200 or 1500A!!!!!!!!!!
  11. jacphi

    electric supply to fire pump

    From purely a technical basis, the continuous current rating of the MCC bus is not really a factor, since the locked rotor current will stop once the fire pump motor either accelerates or burns up. for the above said comment wouldnt it be better if the mcc bus is capable of withstanding the...
  12. jacphi

    electric supply to fire water pump

    i have a controlgear rated for 1200A,480v. one of the feeder is a fire water pump.having a FLA of 240A(locked rotor current 1500A Approx. i am extracting the local std requirement for fire pump unit package. "QUOTE" The protection schemes for Fire Pump Unit (FPU) packages shall comply...
  13. jacphi

    electric supply to fire water pump

    i have a controlgear rated for 1200A,480v. one of the feeder is a fire water pump.having a FLA of 240A(locked rotor current 1500A Approx. i am extracting the local std requirement for fire pump unit package. "QUOTE" The protection schemes for Fire Pump Unit (FPU) packages shall comply...
  14. jacphi

    electric supply to fire pump

    thanks for the reply in fact the fire water pump is fed by a 480v motor control centre. the motor control centre is being fed from the 480v switchgear. i would also like to know if the The fire pump supply must be capable of providing locked-rotor current indefinitely i.e 1500A. should the Motor...
  15. jacphi

    electric supply to fire pump

    i have a controlgear rated for 1200A,480v. one of the feeder is a fire water pump.having a FLA of 240A(locked rotor current 1500A Approx. i am extracting the local std requirement for fire pump unit package. "QUOTE" The protection schemes for Fire Pump Unit (FPU) packages shall comply...
See more

Part and Inventory Search

Back
Top