Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by islandeng

  1. islandeng

    Conception to company w/o experience

    nbucska, i was taught that the patent protected the claims covered in the patent, not the idea itself. The difficult part was (and is) ensuring the claims adequately reflect the idea (so as to protect it from infringing competitors, yet not allow it to infringe on anothers). I also seem to...
  2. islandeng

    Conception to company w/o experience

    Rob, Thanks for your great comments. I'll pick up the book next time i go stateside. I think one of the most difficult lines to walk is this IP protection and idea valuation. Thanks to everyone else for their input as well. Now all I need to do is everything! -islandeng
  3. islandeng

    Well Pump Problem

    I am beginning to think the solution is to use a 904L pump & motor, and give the system some backpressure. I spoke with a new supplier yesterday and he mentioned that the pumps, which are stacked impellers, need to push against some head or backpressure, or the impellers will float around...
  4. islandeng

    Pump Well Problem

    EdStainless, The power coming to the motor is decently clean, three phase. The voltage doesn't vary enough for us to pick it up on our voltmeters, and the phase stays constant at 59 Hz. We don't have an ammeter on the line so I don't know what the amperage is doing, but i would expect it to...
  5. islandeng

    Well Pump Problem

    Hydrae, I have not yet measured the salinity of the water. We have a salinity meter coming in on our next shipment, which was suppossed to arrive last week, however it is stuck in customs (this happens a lot), and hopefully will arrive today or tomorrow.... I was actually using the formula...
  6. islandeng

    Well Pump Problem

    Hydrae, Thanks for your $0.02. I will install a check valve for the next round, however the pump was never stopped in the 3 weeks of operation which led to the pumps failure. There are a lot of less than ideal designs here, which, I believe, all contributed to the failure. Again thanks for...
  7. islandeng

    Conception to company w/o experience

    Thanks nbucksa, I am somewhat familiar with the patent process and patent laws. I took two patent classes and wrote three (fake) patent applications (for what that was worth). I have also taken a course on IP law. The patent search is difficult as the general product has been around for a...
  8. islandeng

    Pump Well Problem

    Rnd2, I have gotten mixed answers, some people have said there have been lots of problems with this pump, and other people (especially the manufacturer) have said there are no problems with this pump, however none of it has been in writing, except through a few emails. The manufacturer...
  9. islandeng

    Pump Well Problem

    Thank you both for your comments. To elaborate on the problem, there are no other signs of corrosion with exception to the small amount on the spline shaft. I am not sure what all the materials are, the pump is manufactured by Grundfos (along with the motor), so I would hope a well known...
  10. islandeng

    Well Pump Problem

    Thanks 25362, I just posted this on the corrosion forum. We'll see what i get! I think i mentioned the temperature in the well is 89 deg F, which is about 31 or 32 deg C, so it is right around the 904L limit....
  11. islandeng

    Conception to company w/o experience

    Greg, Thanks for the advice about NDA's, I signed a bunch of those when I was interviewing for "real" jobs, and had heard through the grapevine that companies did not sign those (or did on a very limited basis). Mac, Regarding your last point, I know and understand that the majority of...
  12. islandeng

    Pump Well Problem

    Hello, I have been having a problem with the splines shearing on a shaft connecting a 2 hp motor to a pump. The pump is located in Brackish-salt water. It was suggested that I bring the forum to corrosion engineering and see what you materials guys can come up with. For full...
  13. islandeng

    Well Pump Problem

    25362, There is some slight corrosion, ie surface rust in the crevises of the splines. It is what I call "rust dust", the type of rust that with a moderate scrubbing comes off easily. I didn't bring this to corrosion engineering forum because my material choices are so limited (basically...
  14. islandeng

    Conception to company w/o experience

    MacGyver, Thank you for your input. I don't want to trivialize what you said, but you would recommend obtaining experience before going out, even if it means loosing the oppertunity. Is that what you were leaning toward? Greg, Thank you as well for your input. You are correct, I would...
  15. islandeng

    Conception to company w/o experience

    Hello, I am a recent grad just hopping around performing 'random' small engineering jobs. Basically, that just means I haven't been hired by any large engineering firms, and people that know me personally have been using my education and paying me for what I have learned. This has been...
See more

Part and Inventory Search

Back
Top