Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

  • Congratulations waross on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by innovation2

  1. innovation2

    316ss vrs 2205ss

    Is 2205 susceptible to MIC???? Maybe this there is something they are concerned with from a microbial stand point since this is an open loop system.
  2. innovation2

    change in thickness of pipe during thermal expansion

    The pipe will expand in all directions, not just length. The change in thickness of the pipe doesn't need to be accounted for in SVIII D1 as the code uses maximum principle stress theory and bi axial stress, I would assume that these small changes in geometry are accounted for in equation...
  3. innovation2

    Test Requirements for small 16 gallon tank

    I think UNF states that this material will require dye checking but you will need to specify to the vessel fabricator the extent of testing you require, i.e. hydro, dye checking, x-ray. Especially if it is fabricated in accordance with the code but not stamped. That statement really gives a...
  4. innovation2

    Nozzle Limit of Reinforcement on Torispherical Head

    I agree with SnTMan. Go with a thicker head or try to use a cone. I would limit reinforcement to the head OD and check the box that "nozzle or reinforcement is outside of spherical portion" of the head.
  5. innovation2

    Design MDMT Vs Rated MDMT

    Ratings for individual components will need to be <= your design MDMT. Essentially you want all parts to be at or below your design MDMT. Regarding how to lower you will need to review the code sections. It is a tricky subject which depends on many different factors. How cold does your...
  6. innovation2

    Dimple Jacket Hydrotest Pressure

    While the design accounts for the diffental pressure acting between the two chambers I do not believe it needs to be tested to the higher pressure. I would argue that you should test at 1.5 x design...not 1.5 x diff. The differental pressure only exists in a vacuum case and if you test at that...
  7. innovation2

    Welding of A-36 and A516 Gr 70

    Both of the materials you list can be welded to the pressure boundary but you need to have an MTR. I specify SA-36 flat bar all the time for vacuum rings and SA-516 Gr70 is an excellent PVQ steel. I use it all the time for pressure boundaries and lifting lugs. SA-36 is typically not used in...
  8. innovation2

    Nozzle local stress due to axial force induced by internal pressure on blind flange

    Do a search for "Pressure Thrust", basically it is what the engineer is asking about. Worth a read at least.
  9. innovation2

    Appendix 13 question

    In App 13-7 it states that he equations in these paragraphs, the moments and moments of interia are calculated on a per-unit-width basis. In your example you would negate the dimension 4 and work on this cross section. Use 13-4(f) to review the end plates. Example 13-17(a) is just about spot...
  10. innovation2

    Appendix 13 question

    I think you need to establish which direction you would like to run your pitch for reinforcement. If it was me, I would remove the end caps and focus on the "long" axis of your cube. The end caps can be considered seperately as braced stay or flat plate.
  11. innovation2

    Full Vaccum Temperature

    Nor will you ever probably acheive full vacuum. It is just a design condition.
  12. innovation2

    Vapor belt (distribution cylinder) vs Jacket Vessel

    The use of App. 9 jacketed vessels is used if the shell continues inside the plenum. You can cut holes/openinings inside the plenum section as long as they are not across the circ. of the cylinder. Typically 3 holes of equal size to vapor inlet are used. If there is a break in the shell then...
  13. innovation2

    SA 516 Gr70 Tube Sheet

    HI heatexguy, where in the code does it list material restictions for TS?

Part and Inventory Search