Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by horacio Torres

  1. horacio Torres

    Flame Arrestors on Natural Gas and Oxygen Vent Lines

    It is extremely challenging to achieve that velocity, and a flame arrestor is not a viable safety device in this case. Horacio
  2. horacio Torres

    Friedel's Model (two-phase) and Noise Attenuation Questions

    The article in the link could help you with your calculations. https://www.linkedin.com/pulse/two-phase-flow-lockhart-martinelli-calculation-method-torres-molina/?trackingId=kWGLWvZNRQqVio2e20aJag%3D%3D Horacio
  3. horacio Torres

    Open-source hydraulic modeling software

    Look for PIPEPHASE Horacio
  4. horacio Torres

    Getting properties for Light Lubrication Oil

    ASPEN EDR is not appropriate for lube oil properties. Do it with Hysys, and design the heat exchanger in Hysys with the interface to EDR. Horacio Torres
  5. horacio Torres

    please recommend me manufactures for waste heat recovery thermal oil heater

    Mitsubishi, backcock for heat exchanger recovery, Horacio
  6. horacio Torres

    PIPING TWO 100% PSV's IN PARALLEL

    If a PSV valve has corrosive service, a three-way valve is installed to allow one to remain on service and the other to be dismantled for maintenance, the operator never will block both. Of course, each one has a ruptured disk attached.
  7. horacio Torres

    Inhibitor to stop polymerization of Chloroprene in EDC-VCM Colum

    Thanks for using my article as a reference Mr Goerge Horacio Torres
  8. horacio Torres

    CDU overhead wash water injection quill plugging

    Ammonia chloride is the suspected horacio
  9. horacio Torres

    Requesting Feedback on P&ID Design for a Cold Water Supply System with Duplicated Pumps

    Terrible mechanical engineer design. Block valves for inlet and outlet pipes of the pumps are obligatory for operational//maintancen job Horacio linkedin.com/in/horacio-torres-molina-429a7b1b
  10. horacio Torres

    Rupture disk downstream of a PSV piping system

    RD is usually used to avoid corrosion on SV, you could install it at each SV. What is not good engineer design is discharging the sv to a vessel, and from it setting a sv to the flare system. This design is used with a recycle pump, for hazardous relief products to recover liquids to the...
  11. horacio Torres

    Nitrogen Purity for Secondary seal gas of Hydrocarbon Centrifugal compressors

    A 100 % agree with georgeverghese Horacio linkedin.com/in/horacio-torres-molina-429a7b1b
  12. horacio Torres

    Heat/Oil radiator possible malfunction

    Internal corrosion could plug some portions of the radiator with debris. It will change the flow pattern and the heat transfer. We had similar radiation troubles in a mobile power plant we faced, so we replaced the radiator. Horacio linkedin.com/in/horacio-torres-molina-429a7b1b
  13. horacio Torres

    CO2 Liqufaction Flow Issues

    The PFD comes from a simulator or is a screen from a DCS. In both cases, which is the simulator? or is a DSC a Yokokawua ???? Horacio linkedin.com/in/horacio-torres-molina-429a7b1b
  14. horacio Torres

    Nat gas supply line to a generator

    Usually 10 tines D of the gas line is recommended Horacio linkedin.com/in/horacio-torres-molina-429a7b1b
  15. horacio Torres

    Should a vibrating screen on springs be considered for Seismic loading

    I wouldn't be considered in the design goracio linkedin.com/in/horacio-torres-molina-429a7b1b
See more

Part and Inventory Search

Back
Top