Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations JAE on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by HBMetals

  1. HBMetals

    Replace failed PTFE liner with Tantaline for liquid bromine?

    Thank you, WKTaylor & moltenmetal.
  2. HBMetals

    Replace failed PTFE liner with Tantaline for liquid bromine?

    Thank you for your advice. I will forward your message to our engineer. BEST www.metalspiping.com
  3. HBMetals

    Replace failed PTFE liner with Tantaline for liquid bromine?

    Another Photo. www.metalspiping.comhttp://files.engineering.com/getfile.aspx?folder=cbfa2f16-c573-4ec9-910c-dbad418d418b&file=001.jpg
  4. HBMetals

    Replace failed PTFE liner with Tantaline for liquid bromine?

    Hi engineers,we are trying to replace several PTFE lined steel pipes for a liquid bromine line. Pressure rating: 0.2 MPa, Temperature: room/ambient. Please see the attached 3 photos: the flanged steel pipes are lined with PTFE. A small hole was drilled on each end of the pipe to supervising...
  5. HBMetals

    Which Ti grade is most compatible to water saturated with chlorine and salt traces

    Sorry that there's a typo. It should be Ti Grade 7 "Ti-0.15Pd". The nominal composition of Grade 16 is "Ti-0.05Pd". They have identical mechanical properties. However, compared to Gr.16, Gr.7 is more often applied in corrosion applications since there are more approved engineering experiences or...
  6. HBMetals

    Which Ti grade is most compatible to water saturated with chlorine and salt traces

    I think I have a technical literature which says Ti-0.5Pd (Grade 7 titanium) is a TYPICAL crevice-corrosion-resistant titanium material for industrial application with Cl ion ≈ 20%, PH2, 120°~130°C. The application is concentrator equipment in salt purification. Due to the large size, just...
  7. HBMetals

    Carburising Astm A-216 WCB

    Generally, carburization is suitable for low carbon steel(0.1%~0.25%). It is reported that there are new carburization techniques for high-C materials, however, what's the meaning here? I don't get it. www.metalspiping.com
  8. HBMetals

    LCB Heat treatment

    Sorry for the late reply. I just come back from vacation. One of my fellow engineer says it seems that your chemical composition is inapproriate. As a rule of thumb, we should adhere to "Low-Carbon High-Manganese" principle in the production of LCB casting. An actual chemical composition is...
  9. HBMetals

    LCB Heat treatment

    Our engineer once did this heat treatment experiment on LCB casting specimens and I just find some documentation and try to translate the literature partially: three LCB specimens(A, B, C), chemical composition analysed by spectrum apparatus - ok, Specimen A: Normalized + Tempered. Normalizing...
  10. HBMetals

    SA-387 9 Chrome Plate

    metengr is right. ASME SA387 Gr.9 plate is not within the jurisdiction of ASME BPVC Section VIII Division 1. It can't be used. I also did a thorough search on Code Cases - 2015 Edition. So far nothing regarding 9Cr-1Mo is found. However, I have a question: when a new edition of code Cases is...
  11. HBMetals

    HIC & SSC test

    Sulfide stress cracking(SSC) is a special case of hydrogen stress cracking, also known as hydrogen-induced cracking(HIC). This cracking mechanism depends on several factors:hydrogen fugacity, material strength, heat treatment/microstructure, applied stress, and temperature. For many steels...
  12. HBMetals

    ASTM A588 steel plates cladding for a city's landmark

    Dear Hokie66, dhengr & Edstainless, thanks for all your valuable advice. I didn't reply them yesterday because of time difference. For clarification, we are talking about the refurbishment of the 31-meters(102 feet) monument behind the horse statue. You are right, hokie66, the refurbishment work...
  13. HBMetals

    ASTM A588 steel plates cladding for a city's landmark

    Racookpe1978, thanks for your prompt reply and advice. Bronze may be a good idea. However, instead of changing the whole stone monument to bronze statue, the municipal government at present just consider a metal sheet cladding. Could you please recommend a bronze specification for sheets /...
  14. HBMetals

    ASTM A588 steel plates cladding for a city's landmark

    Dear engineers, I am not sure whether this is the right place to pose this question. Recently one of my friends is working on the refurbishment of our city's landmark - Liberation Monument(please see the photo attached). This monument, about 31 meters tall, was made of giant stones about 30...
  15. HBMetals

    A694 F65 flanges manufactured to ASME B16.5

    Thanks for your reply, BigInch. I raise this question is because those F65 flanges supplied were approved by an authoritative Third-Party Inspection corporation appointed by the customer. To my astonishment, they just reviewed the MTR and checked some dimensions. My understanding is A694...
See more

Part and Inventory Search

Back
Top