Nice to see this subject on the agenda.
As an Aussie, I deal with both civil and military regulators who are both quite anal about their requirement for independent verification of the adequacy of designs.
I personally like to see my analyses verified. It saves grief later.
I have found that the...
KirbyWan,
Boeing have a series of standards for their placards which depends upon application. I'm sure that McD had similar.
Take care to use suitable alternate materials. Remember to edge seal, and make it from really tough abrasion resistant material next time, or better train staff.
"the sky...
G'day canes0714,
Sealant ain't just sealant.
You will need to identify the type before a suitable dissolver can be found:
Silicone?, polyurethane?, polysulphide?
Is it an aircraft application?
You might like to try the SPS website for inserts of the style you seek.
http://www.spstech.com/aero/products/inserts/staked_inserts.html
If you give them the Boeing pn tehey may well be able to provide a suitable alternate. You will probably need to seek an independant approval for it though...
G'day thruthefence,
The requirement in the FAR's is for Controls, and a system that locks/unlocks a tailwheel is a control.
If it was certified with a cable rubbing where it shouldn't, it points to an inadequate certification process.
The first person to touch it will be duty bound to fix it and...
G'day Foglights and Wil
I'll add my little bit if I may.
Will you are quite correct in what you say and if Foglight looks in FAR27.685 he will see the following (extract)
(a) Each detail of each control system must be designed to prevent jamming, chafing, and interference from cargo...
G'day Karl
You need a list of requirements to fill out before you can get started:
1. Certification basis for compliance purposes
2. Power characteristics:
2.1 Duty cycle,
2.2 Power requirement (watts)
2.3 Voltage input, voltage AC or DC
2.4 Voltage output, voltage AC or DC
If AC, single phase...
wktayor
G'day Wil
Loctite advise that:
"The Primers concerned have copper salts (in minute quantities) to serve to accelerate the polymerisation (curing) process of the anaerobic.
Primers are used in circumstances such as:
inactive metals (eg Stainless Steel etc)
need to reduce cure time...
G'day rb1957:
I confess that I agree with you about wanting a bit more info.about CSK fillers.
I also have called them up for use, and unlike the experience of others, mostly they have been used. Maybe because I "hover around" at times and they are afraid that I will catch them leaving them...
G'day mate,
Like many areas of endevour, academic quals. will only take you so far.
The Flabel course is a good one on practical stress analysis but it will still only give you the basics. Yes, it is basically what is in the book.
You will need to get out there and apply the lessons in a...
G'day Istambul
As 737eng says, changing the pitching of fasteners in a fitting can vary the load distribution between the fasteners, as well as the reactions to applied loads which may have a component parallel to, but displaced away from the mating surfaces.
Without knowing what the fitting...
Gooday Wil
Thanks for the response,
The issue is with the Loctite Primer. It gets sprayed on quite liberally at times and sometimes is not adequately washed off afterwards (it is solvent based and I have seen procedures not calling for a wash afterwards).
You are correct in regard to isolation...
G'day Wil
A caution on the use of Loctite primers. I was advised by a Loctite rep. some years ago that these contain a very fine dispersion of copper or iron (depending on the primer type)to catalyse the adhesive, which should be washed off after the Loctite has set. My experience of the use of...
A complicated subject with an empirical base, connected to effective sheet widths. See Bruhn Section C7.12 to C7-20 for discourse. Fir is elastic, wrinkling is plastic.
With staggered rows, use the lengthwise spacing of each row to calculate Fir for each row unless the 1/2W calculated from the...
Uniaxial compression with a superimposed shear is wing torsion box upper skin stuff. Provided that the panel is bounded by stiffeners (aka stringers and ribs) the panel will carry substantial shear even though the onset of buckling may occur at relatively low stress.
The mix of shear and...
