Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by GB1000

  1. GB1000

    Timoshenko - Cantilever with point load at a distance 'x'

    Thanks all. I have come across a formula in a FRP composite book. This takes into account both shear deformation and bending deformation. I'd be interested to compare this answer with denial idea (when I get time)...
  2. GB1000

    Timoshenko - Cantilever with point load at a distance 'x'

    The material is a FRP e-glass. My understanding is with these products because of the low modulus shear deflection will occur
  3. GB1000

    Timoshenko - Cantilever with point load at a distance 'x'

    I’m not sure this is correct with rotation and deflection? How does this take into account shear deformation? This is a composite material where shear deformation will account for some of the deflection. I’m tendering to agree with 3DDave. This is a anisotropic material.
  4. GB1000

    Timoshenko - Cantilever with point load at a distance 'x'

    @3DDave, you mean change the title? You are correct, Euler-Bernoulli is ineffective for that reason.
  5. GB1000

    Timoshenko - Cantilever with point load at a distance 'x'

    Update: Found a formula relating to Timoshenko. is this the answer or is this purely for the deflection at the tip
  6. GB1000

    Timoshenko - Cantilever with point load at a distance 'x'

    I'm after some experts to assist with Timoshenko. I'm trying to calculate the deflection at the tip due to shear deformation and loading. I've found many formulas showing deflection at tip when the load is at the end, however none where the point load is at 'x' I know of Pa^2/6EI x...
  7. GB1000

    RE: AS3600-2018 Cl 2.2.3 (b)(ii).

    @just some nerd. Yes, in summary, calculate the confining pressure and apply the formula. Quite an interesting read when you get into it. I would have thought ligs/legs @ 200 spacing would be fine, by the code directed to a minimum of 150mm.
  8. GB1000

    RE: AS3600-2018 Cl 2.2.3 (b)(ii).

    All good. Refer to AS3600-2018 commentary
  9. GB1000

    RE: AS3600-2018 Cl 2.2.3 (b)(ii).

    Hey Team, I'm after a bit of advice regarding Cl2.2.3 (b)(ii). We have a shear wall where the vertical bars are tied together with legs at every 200mm spacing. My question is what value of β would you use? The code stipulates 'in regions where effective confining reinforcement is...
  10. GB1000

    AS3600-2018 Post Tension (Cl 9.5.2.3)

    Good point Rapt and appreciate the comment. How would you define 'short term service loads' as this is what the clause specifies? Would you define this as the as the self weight and tendon uplift (i.e. transfer load), or defined as something else?
  11. GB1000

    AS3600-2018 Post Tension (Cl 9.5.2.3)

    Hey, The item below refers to a post tension slab design I'm slightly confused on the wording which AS3600 uses for this clause.... 'if this stress is exceeded, by providing reinforcement or bonded tendons, or both near the tensile face with a centre to centre spacing not exceeding the...
  12. GB1000

    AS2870 Building Raft Foundations on top of ground

    Yes not a problem, AS2870 even allows upto 400mm of fill to be placed in 200mm layers; rolled and compacted. this would be deemed as controlled fill. However I would generally just put some backhoe piers in through the fill so you are not relying on workmanship
  13. GB1000

    Crane Beam Example Australian Standards

    Hey team, I've got to design a crane beam and I'm jus wondering if anyone has any guidance or literature they can direct me to. I know its to AS1418 Thanks
  14. GB1000

    Siesmic Loading on ducting/piping

    Thanks guys, yes I did some more research on this and it appears got hangers are not a good idea. There we end up using diagonal struts to resist the lateral forces.
  15. GB1000

    Siesmic Loading on ducting/piping

    Hi, I've been instructed to perform siesmic loading on ducting and pipework which is already built. i The existing detail is basically two M12 rods which hang from for above slab supporting the duct. the connection of the M12 rod is basically fixed in to the slab providing a rigid...
See more

Part and Inventory Search

Back
Top