Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by foxymophandlpapa

  1. foxymophandlpapa

    ASME Section VIII Div. 1 Vessel Stamp

    I found it, thanks for all the help JT.
  2. foxymophandlpapa

    ASME Section VIII Div. 1 Vessel Stamp

    Thanks, we have an IHS subscription. Is it listed under "Interpretations Volume 57"?
  3. foxymophandlpapa

    ASME Section VIII Div. 1 Vessel Stamp

    Thats perfect JT. Can you post a link to that volume?
  4. foxymophandlpapa

    ASME Section VIII Div. 1 Vessel Stamp

    Thanks JT. I definitely agree with the definition explanation. Obviously if ASME will define FV, then I'm sure they would accept it on their vessel. As for UHX-19.1, unfortunately thats for heat exchangers and they could deem that not applicable since this is a 50 L vessel. All the same...
  5. foxymophandlpapa

    relief valve set pressure Q

    Set the burst pressure the same as the PSV set pressure: 25 barg.
  6. foxymophandlpapa

    ASME Section VIII Div. 1 Vessel Stamp

    This is a question regarding the specified MAEWP on the vessel's stamp. We would prefer that our vessel's MAEWP says "FV" but the tank vendor refuses, saying code requires them to put an actual number. Currently, they are showing "15 psi". First, I find "psi" as a very gray area, especially...
  7. foxymophandlpapa

    Old ASME vessel, new PSV

    Thanks for the info all, but none of this is in my scope. Sizing the PSV is the part of my scope. For "conservative" reasons, we will size the rupture disk according to API 2000.
  8. foxymophandlpapa

    Old ASME vessel, new PSV

    Does ASME have a requirement for testing pressure vessels after a given amount of time? Pleckner does have a point that it has probably eroded with time and has weakened the vessel, but unless there is something that explicitly states we must test the vessel before designing a new PSV for the...
  9. foxymophandlpapa

    Old ASME vessel, new PSV

    Pleckner, Is a vessel that is stamped in 1973 and is unmodified still valid as ASME, though it no longer meets ASME standards? If this vessel were designed today with its current specs, it would not get a stamp. This vessel's operating or design pressure does not exceed 15 psig. Our...
  10. foxymophandlpapa

    Old ASME vessel, new PSV

    Actually, I think thats a misinterpretation. It only refers to OPERATING pressure, not design pressure. If my vessel has a stamped MAWP of 15, which doesn't EXCEED 15, then that means I'm OPERATING below 15. Since ASME states that my operating pressure must exceed 15 to be an ASME vessel...
  11. foxymophandlpapa

    Old ASME vessel, new PSV

    Under the Scope U-1(c)(2): Based on the Committee’s consideration, the following classes of vessels are not included in the scope of this Division....(h)(1)vessels having an internal or external pressure not exceeding 15 psi (100 kPa);
  12. foxymophandlpapa

    Old ASME vessel, new PSV

    I'm not about to search thru the code, but ASME.org's website says for Section VIII - Pressure vessels Div. 1: "This Division of Section VIII provides requirements applicable to the design, fabrication, inspection, testing, and certification of pressure vessels operating at either internal or...
  13. foxymophandlpapa

    Old ASME vessel, new PSV

    But my vessel is not an ASME vessel, according to ASME section VIII div. 1 because the MAWP does not EXCEED 15 psig. Its MAWP is exactly 15. BUT, it is stamped, back in 1973 as an ASME vessel. If I put an ASME relief valve on it, I can't have a 15 psi setting. If I put a conservation vent...
  14. foxymophandlpapa

    Old ASME vessel, new PSV

    I have a vessel with a MAWP of 15 psig, stamped as an ASME vessel back in 1973. We're relocating this vessel and a new PSV needs to be provided. Current ASME Section VIII Div. 1 states that to be a pressure vessel the rating must exceed 15 psig. How should I approach this relief...
  15. foxymophandlpapa

    API 521: Tw (vessel wall temperature)

    I'm using equation 5 in API 521 to calculate the relief orifice size of a gas filled vessel. The explanation for the Tw value isn't very specific. Am I supposed to use the maximum wall temperature? Otherwise it would seem that Tw would just be equal to Tn, the normal operating gas...
See more

Part and Inventory Search

Back
Top