Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by finite

  1. finite

    Pumping of Chocolate

    thanks guys for all the help. the project is complete and a great success. the client now wants to extend the system by another 20%. The original system was, so I have been told, the longest chocolate piping system in the world. Once again thamks for the info
  2. finite

    Noisy Vacuum Pump

    Thanks for all the answers. I was told yesterday that the manufacturer had welded ribs on the ensd of the blades. Now the ribs have been removed the pump is running quietly Finite
  3. finite

    Noisy Vacuum Pump

    I am running some new vacuum pumps that we have just purchased. All the pumps are the liquid ring type. The pump is quite to a pressure of approx 80 Kpa(negative). As soon as I close the suction port to reach a pressure of 88 to 92 Kpa(neagative) the pump becomes noisy. I have checked that I...
  4. finite

    Pumping of MDI resin

    I am involved in a project to set up a particleboard factory. I would like to design a bulk staorage facility. i need to know what type of pumps i should use for the pumping of the MDI resin (Diphenylmethane diisocynate) Finite
  5. finite

    Steam Reduction

    What is the maximum pressure differential that could be used for acurate control through a steam control valve. The pipe diameter on the inlet is 2 inch?
  6. finite

    Pumping of Chocolate

    I am involved in a project that requires the pumping of chocolate. I am looking for information regarding the pressure drops in pipes as well as pressure drops in fittings, such as bends, valves. I would like to know if anybody has some tips regarding the reticulation of chocolate? Thanks Finite
  7. finite

    move all dates

    Dear Blooda Open The toolbar "Analysis" in MS Project. On this toolbar you wil find "Adjust Dates". This function will move your project to the required date. Hope this is what you need? Regards Finite
  8. finite

    section properties

    Butelja Thank you for that tip. It works 100% Thanks once again. Regards Finite
  9. finite

    section properties

    I am looking for a lisp routine for the calculation of section properties. I would like to be able to draw a section in autocad and then extract the section properties.
  10. finite

    PIPE COILS

    I AM LOOKING FOR INFORMATION TO CALCULATE THE PRESSURE DROP ACROS A PIPE COIL.THE TYPE OF COIL I AM REFERING TO IS THE TYPE THAT COULS BE FOUND IN A LIQUIR STILL OR TRACE HEATING FOR A PIPE. REGARDS FINITE
  11. finite

    course for fluid mechanics of coating

    I am looking for the name of the university in the USA that offers a course for the fluid mechanics of coating.I have seen it somewhere but did not bookmark it. If any one could help
  12. finite

    I am looking for a manual for the design of conveyors. It must cover t

    I am looking for a manual for the design of conveyors. It must cover the following: screw conveyors, belt conveyors, chain and bucket conveyors. I have seen two manuals from two different manufactures<br>1. The Jeffery Manufacturing Company Columbus 16,Ohio(Catalogue 418)<br>2. Link Belt Limited...
  13. finite

    Spiral wound channel

    I have a heating drum used to to heat PVC sheet.The drum has a diameter of 600mm. A spiral channel is inside the roller to provide good heat transfer from the heating fluid to the PVC sheet.The size of the channel is 30mm wide x 12mm<br> deep. The overall length of the drum is 3.6m. The drum...
See more

Part and Inventory Search

Back
Top