Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by eric34

  1. eric34

    Remote Reset for circuit breaker

    currently We are using a telemecanie but I am looking for a difernet type that can be rest from the outside of the door.
  2. eric34

    Remote Reset for circuit breaker

    In are sawmill we have several VFD's with multable motors on them. If one of the curcuit breaker tripss and an electrican has to open the cabinet and reset it. I am looking for a breaker that can be reset from the outside of the door. Does anyone know if there is any reliable units out there...
  3. eric34

    Motor Amperage.

    I am looking into a load monitor, they seem to be what I am looking for but am not fimilar with the brands. Can anyone out there suggest a good, reliable unit that is ethernet ready? Network capable is a must.
  4. eric34

    Motor Amperage.

    250 HP is the motor size. The Motor isn't failing under normal conditions.. The pressure line was the main cause and my boss was looking for better protection....The motor is running as we speak. I am afraid that the normal running amperage will change as the motor gets worn, overheated. .Then...
  5. eric34

    Motor Amperage.

    The blower is for are wood chips. Feed the chips using a chip feeder and the blower produces high volume, low pressure. If you are looking for the manufacture, I would have to get back to you. The real only question I am looking for is how much would the amperage change if the motor is new...
  6. eric34

    Motor Amperage.

    I have a Blower motor that we are having problems with. We monitor the pressure in the pipe going to the cyclone. If the pressure gets to 5 PSI we shutdown the feed, if the pressure gets to 7PSI we shutdown the blower motor. Last week we had a small hole in the pressure line going to the...
  7. eric34

    Graphics for factory suite

    Does anyone know the link to more graphics for factory suite ?. I would like to add to my libary. I looked but I don't know the proper name for it...
  8. eric34

    using the interlok wire on a smoke detector

    it isn't for fire control system. The inspector just wants the fans to go off if there is a sigh of fire. Looking into it more Kidde does make a relay that would work good. Thanks for your help ALL
  9. eric34

    using the interlok wire on a smoke detector

    I am required to turn off a fan that feeds fresh air to acouple of rooms. The rooms are finished and surface wiring isn't an option. If I could use the interlok wire that interloks a regular smoke detector together that would be the simplest but was unable to find what signal they us to turn...
  10. eric34

    usb to RJ 45 cable

    Hello All, I need to run a USB port about 100 FT from my PC. Can I make up a cable to convert to RJ 45 and back to USB at my destination?? I see there are cables out there but I would like to learn more about this.If I can do this what is the max distance one can run...
  11. eric34

    Got a shock at work and a little puzzled on how.

    I got a call to a VFD drive not working.I found that the drive had lost it's smoke(burnt up) and a load reactor was also burnt.I tested the motor to ground and everything was good.I wired up a new drive and everything was good.About an hour later I got a call saying that the drive was working...
  12. eric34

    Need a ONS in a SLC 5/03

    I am use to using PLC 5 or control logix and I need a one shot instrution in the old slc,it doesn't seem to support it.Is there something in the S2 file I can use?
  13. eric34

    Looking for some hardware.

    Sorry ScottyUK I need to have a touch pad to punch a password to access some controls.Are plant is all on control logix 5000 but a old loading chute(Hyd tank and two divertors) are not on a PLC.There is no need for one but they would like to have it password protected, I thought I would wire...
  14. eric34

    Voltage drop across safety prox switches

    You could turn a relay on with each prox.and have the contacts of the relay in series, that way you would have full Voltage at the end. If you wanted to wire a dummy light in Parrallel with the relay coil and this would give you quick referance to what proxes are not making.
  15. eric34

    Looking for some hardware.

    I am looking for a Interface panel. I need to punch in a password and the unit to give me an output.120 VAC would be nice but can be different.All the ones I could find are ether very pricy or are more complex than I require.Thanks
See more

Part and Inventory Search

Back
Top