Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by daveo

  1. daveo

    External HP dat device on WinNT 4.0

    bpatt, the problem in the end was that the dat device was dds4 and was not backward compatible with orignal dds tapes. thanks for your reply.
  2. daveo

    Time to Cracking in Spray Quenching of Steel

    I've managed to find the 'time to the onset of cracking' using a transient analysis, Daveo
  3. daveo

    Please help! I'm getting the follo

    Dear all, thanks for your info, but unfortunately our IT sub contractors took away the machine and reformatted the disk. However, like SVANELS pointed out the machine count not be started in DOS mode due to the absence of the DOS mode partition, but Til's solution may have worked. Our IT people...
  4. daveo

    External HP dat device on WinNT 4.0

    External HP dat device on WinNT 4.0 reads 'tape is write protected' when trying to archive stuff on a new tape which is not protected. Has anyone have ideas on how to overcome this?
  5. daveo

    The dat tape device is not respondi

    The dat tape device is not responding (external scsi device on sgi impact). Does anyone have any simple hints on how to reactivate it? Thank you in advance!
  6. daveo

    Time to Cracking in Spray Quenching of Steel

    I wish to calculate the time it takes for steel bars (2 types, 4140 steel and EN30B steel) to crack in a spray quenching tank. Because only the sides of the bar is sprayed, cracking occurs at its ends. Can someone give ideas on how I should go about calculating when cracking will occur from the...
  7. daveo

    Need to reinstall MSVCRT.DLL but its in use by Windows

    Thanks Yakpol, but this does not work on NT.
  8. daveo

    Please help! I'm getting the follo

    this does not work on NT thanks anyway, Rich
  9. daveo

    Need to reinstall MSVCRT.DLL but its in use by Windows

    Please help! I'm getting the following warning message when I launch most applications (MathCAD, IE5, AutoCAD, etc) "The procedure entry point ??_U@YAPAXI@Z could not be located in the DLL MSVCRT.DLL" I need to reinstall MSVCRT.DLL but as its in use by Windows NT it wont let me! CAP...
  10. daveo

    Please help! I'm getting the follo

    Please help! I'm getting the following warning message when I launch most applications (MathCAD, IE5, AutoCAD, etc) "The procedure entry point ??_U@YAPAXI@Z could not be located in the DLL MSVCRT.DLL" I need to reinstall MSVCRT.DLL but as its in use by Windows NT it wont let me! CAP...
  11. daveo

    system file on NT needs replacing but its in use during session

    I'm using Windows NT4 With this system I cant seem to boot up in DOS mode. I'll try registering the file using the regsvr32 command. Thanks for your help
  12. daveo

    system file on NT needs replacing but its in use during session

    I'm getting the following error message: The procedure entry point ??_U@YAPAXI@Z could not be located in the DLL MSVCRT.DLL I need to reinstall MSVCRT.DLL but its in use by Windows NT and wont let me! CAP GEMINI ERNEST & YOUNG COULD NOT SOLVE THIS PROCEDURE!!! ANY TAKERS??
  13. daveo

    length of a polyline?

    thanks both Reaver and Butelja Daveo
  14. daveo

    length of a polyline?

    I'm trying to find the length of a polyline? thanx in advance kind regards, daveo
  15. daveo

    Spray quenching.Cooling capacity of water-air mixtures.Applications

    Hi Roxana, I'm presently trying to simulate a quench cracking problem of steel. Since I know little on the subject, below are some sites I came across that gave me some lead. Some of the terminology may help during searches: Unfortunately, I dont think theres a specific reference to water air...
See more

Part and Inventory Search

Back
Top