Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by casflo

  1. casflo

    Liquid Droplet Impingement

    The nuclear power plants watch carefully the thickness of the carbon steel pipes where the fluid is flashing water or wet steam. Look for a document of EPRI (Electrical Power Research Institute) that has by title: "Recommendations for controlling cavitation, flashing, liquid droplet impingement...
  2. casflo

    RO Sizing

    The attached paper helps to analyze the acoustically induced structural fatigue in pipes caused by throttling devices...
  3. casflo

    Design a Flow Orifice to take down DP to Closed Drain

    I agree with the previous answers. It is not a good idea to drain a liquid and a gas through the same pipe, even if done separately. In any case, the orifice design should be of multi-stage type, each stage consisting of a multi-hole plate. This design will prevent cavitation in the case of the...
  4. casflo

    High Pressure separator Level Control Valve position U/s or D/s a HeatExchanger / Heater in a GOSP

    Shvet, I´ll try to clarify your doubts. My previous comments assume that the topicstarter has a single C. V. that wants to know what is the best option to install it. From the data of the Option A, assume to simplify that the pressure drop in the pipe from the H. P. Separator to the HX outlet is...
  5. casflo

    High Pressure separator Level Control Valve position U/s or D/s a HeatExchanger / Heater in a GOSP

    Shvet, I agree that there are not enough data to fully analyze the question. The fluid vapor pressure, the height between both separators, the C. V. pressure drop ,etc. are unknown. But in relation with the possible flashing of the oil stream, other aspect to take into account, is the influence...
  6. casflo

    High Pressure separator Level Control Valve position U/s or D/s a HeatExchanger / Heater in a GOSP

    In the case that the fluid flashes passing through the valve, the Option B is the best. The scenario is similar to the cascade heater drain system of the power plants, where saturated water passes from a condensate heater to other with less pressure through a drain pipe with a level control...
  7. casflo

    Butterfly Valve - Pipe Wear

    From your post, it appears that the actual flow control is acceptable and the problem is the valve cavitation when it operates at openings less than 30%. It is possible to eliminate the cavitation in the valve, by symmetrically drilling several holes in the valve disc, making it a multi-hole...
  8. casflo

    what could be the reason for the da

    Probably the cause of the damage is the cavitation. If the water temperature is 180ºC, its vapor pressure is approximately 10 bara and the cavitation index is (265 - 10)/(250 - 8) = 1.05 You need a valve with a cavitation coefficient equal or less than 1.05 The damaged valve surely has a...
  9. casflo

    Hot water flow from open pipe end

    As the pipe is only 4m long, practically the flashing occurs at the pipe exit and you can consider that the critical pressure at the end of the pipe is the saturation pressure of the water with 146 ºC. Therefore, calculate simply the flow rate of water through a pipe 4m long and 100 mm diameter...
  10. casflo

    Control valves and velocity

    Snickster, A throttled valve has a significative frictional pressure drop, therefore the expanansion is closer to isenthalpic than isentropic. For example, in a nozzle, as in the case of a steam safety valve, the friction is very low and the expansion is close to isentropic. In any case, the...
  11. casflo

    Control valves and velocity

    The steam passing through the valve has an expansion close to the isenthalpic. With an inlet pressure of 270 psi and the valve discharging to a zone at 10 psi, the valve has choking conditions in its throat and the pressure here will be approximately 135 psi. Therefore, to calculate the velocity...
  12. casflo

    Steam Trap Outlet Condensate Temperature

    Usually, you can consider that the condensate is saturated at the steam trap outlet. It can get subcooled in the draining piping if it has not thermal isolation.
  13. casflo

    Estimation of price per kilo

    Try in this website: totalmateria.com
  14. casflo

    Air System Blowdown Analysis Struggles

    There are not data about the design of the blowdown line to depressurize the tank. If it is a short pipe with a valve that has a inner pass section little than the pipe, consider only the valve where the flow of air chokes. To calculate the air flow rate through the valve, use the equations and...
  15. casflo

    heat loss through insulated pipe line

    Dear pradeep4u, I only want to say that the steam and whichever other compressible fluid, has a pressure drop (expansion) flowing along the pipe, that cools it. This expansion along the pipe is close to an intermediate value between the isentropic and the isenthalpic expansions. If the expansion...
See more

Part and Inventory Search

Back
Top