Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by cammax

  1. cammax

    installation of cables

    yes MI cable, sorry is Bus duct cheaper then MI cable? we went with MI cable due to retro-fitting and space limitations.
  2. cammax

    installation of cables

    Have you thought about MIC Cable? we have used it to feed Mission critical locations and Fire pumps as well, speed of installation offset the the material cost for our project.
  3. cammax

    tank heating coil

    not sure what reg But I thought NFPA limits steam pressure for F/O tanks #6 to 15 PSI max...
  4. cammax

    hmm, todays news

    HAHA, no figured I would get input from people who know a whole lot more then I. It is on a respected news source and you know the sheep will believe it.
  5. cammax

    hmm, todays news

    http://money.cnn.com/2006/09/15/technology/disruptors_eestor.biz2/index.htm
  6. cammax

    Help With Liebert 3000 Unit

    68 deg F is really to cold for a Liebert, I belive there spec's say they are ok down to 68 but they perform much better at 72 deg F and that should be there field Min setpoint for temp, as for humidity pushing this much below 50% on DX alone might be trouble some, I hope you have a tight vapour...
  7. cammax

    What is this structure called?

    Gantry crane or gantry support http://www.lkgoodwin.com/more_info/t_series_gantry_cranes/t_series_gantry_cranes.shtml
  8. cammax

    alternate engine design

    better link for you http://www.rotaryengineillustrated.com/animations.php
  9. cammax

    alternate engine design

    http://www.math.tu-cottbus.de/INSTITUT/lsnmwr/eggers/rotory.html or this?
  10. cammax

    Insulation of Car Exhaust

    I would think cooling,the exhuast flow at the exh ports would improve scavenging, which would increase HP but decrease MPG, not sure what the torque would do. but it would be like a condenser on a gas turbine... thoughts? ( just me thinking outloud)
  11. cammax

    Steam "Wetness" in Benchtop Steriliser- Measure?

    we have come across this many times, there are 2 products to measure steam quality 1) A condensing steam "calirometer" 2) very exspensive high temp humidity sensor the first one is reletivly cheap but has a very wide margen for operator error. that said we have found the best solution in our...
  12. cammax

    Data Logging of a Chiller

    I dont have enough info - But that sounds more like a very lightly loaded chiller. What type of chiller - if possible provide brand and model #
  13. cammax

    Tuning motorcycle carburettors

    I'd say where on the same page, I have those books and there pretty worn out from years of use. We have dimpled our intake runners to create small eddy's to help in A/F mixing and actually slightly reduce air flow (Yates SB ford Heads -nascar take offs) that where opened up a bit much for...
  14. cammax

    Tuning motorcycle carburettors

    "Additional note...your peak power will be found at 12.5 to 13.8 to 1. Not lean at all. Lean is mean is an old term and will lead to disaster. If you tune for peak power you will not be lean at all." in a nut shell..your wrong and right, Peak HP will be achived at 14.7 to 1 A/F ratio the...
  15. cammax

    Tuning motorcycle carburettors

    http://www.corsa-inst.com/ezprices.html they sell products like what I have built myself but they cost a whole lot more :)
See more

Part and Inventory Search

Back
Top