Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by CADone

  1. CADone

    3GB switch in Solidworks

    Vinay, I found a video. Try this. But, as Kellnerp mentioned, its suitable for 64 bit OS. http://www.screencast.com/users/CADGeeks/folders/Jing/media/c76d7a7e-5cdf-4e80-8629-a0e7a40ffc65 Thanks, C1
  2. CADone

    Apparent intersection point size

    Thanks guys. This forum is so helpful. This is one of the reasons I like SolidWorks. Sorry abt the heavy file. I dint bother to check before it uploading.
  3. CADone

    Apparent intersection point size

    The style is set perfectly to my requirement. But I dont find how to adjust its style. See attached. The VS lines are too big.http://files.engineering.com/getfile.aspx?folder=64b5260a-10cc-4da1-9e09-e17ab29cc77a&file=dele.bmp
  4. CADone

    Apparent intersection point size

    Thanks for your advice here, CBL. thread559-201967 In a drawing when I create a point (Holding 2 edges)the, an apparent intersection point is formed. Is there a way to control the size of it. Its tooo big. Thanks C1
  5. CADone

    Designing castings in SW 2009

    Another approach, you could try creating configurations in 1 part file "Machined" & "Unmachined".
  6. CADone

    Thermal analysis related addin

    So silly. I was already answered for this before. javascript:openindex(450,450,'http://www.tipmaster.com/includes/refinfo.cfm?w=450&h=450')
  7. CADone

    Thermal analysis related addin

    Hi, I have designed Al diecast housing. On this I mount PCBs with many Diodes (sources of heat). I need to verify if the heat sink fins on the housing is meeting the minimum requirements for heat decipation. Basically the whole system needs to maintain thermal equilibrium. Its natural convection...
  8. CADone

    Ordinate dimension-Change origin question

    Thx for the quick help
  9. CADone

    Ordinate dimension-Change origin question

    I have a drawing file. The view consist of a rectangle (Plate face) with several circles (Holes). On my drawing view, I need to use a ordinate dim. My origin is in the center of the plate. I have ordinate dimentioned all the holes (ver and hor) Needed change : I want the odinate to be changed...
  10. CADone

    Roll forward not working?

    Hi I have an assembly. When I open it I get the following message. "This document contains other parts and/or assemblies that were saved in a rolled back state. Do you want to roll them forward?" I accept the message. Force Rebuild all (Ctrl-Q), Save it. Do this for each cfg. Open each part...
  11. CADone

    Dim control & Cfg

    Thx CBL. I belive this will fix.
  12. CADone

    Dim control & Cfg

    I wish I could tie the feature to the origin even in the model. The reason is that I need to create a single rectangular pattern feature to have extrude on both sides of origin. like : [E] [E] [E] [E] [E] C/L [E] [E] [E] [E] [E] tHX C1
  13. CADone

    Dim control & Cfg

    Hi, I need help in setting up a dim for various configuration. I have 2 configs in a part. config1 : As you can see in the attached file, the dim 2.25 is to the left side of the origin. Its important for this dim to be starting from the origin. Config 2: I need this value to be 0. My...
  14. CADone

    Array fillets

    For mysake, I wished I could send the part but I cant. I could figure out more details. Actually I can pattern the extrude and the fillet. But there is also a draft of 3 deg on that extrude. This is the issue, it wouldnt array. Dont know why. I have unchecked/Checked the geometry pattern also...
  15. CADone

    Array fillets

    Hi Why cant we array the fillet on the extrudes. See attached img. After the rectangular array, I need to use this rect array in a circular array. Thx C1
See more

Part and Inventory Search

Back
Top