Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations MintJulep on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by bhart

  1. bhart

    Spring Preload in Single Seater Race Cars

    Regarding the wheel rate: Things with an "s" after the underscore refer to a spring quantity, things with a "w" refer to a wheel quantity. F_s = force in spring F_w = force at wheel (vertical) z_s = deflection of spring z_w = deflection at wheel (vertical) MR = deltaz_s/deltaz_w =...
  2. bhart

    NEED SIMULATION INFO

    Billy, Your last expression appears very similar to my original expression which I stated I only had partial confidence in (same terms anyway)... have you tried to solve for the ratio of RF to LF wheel rate to see if it comes out the same, that would be encouraging if it we independantly...
  3. bhart

    NEED SIMULATION INFO

    Well, most people wouldn't classify me as old just yet, so in my case, it's just another senile engineer.
  4. bhart

    NEED SIMULATION INFO

    Billy, I recently went through the painstaking process of writing out long hand expression for all of the dynamic load transfer components on my type of racecar. I have a live axle @ the rear w/ a torque tube, and a solid axle up front. I think most drag cars probably have independent...
  5. bhart

    Chamfer or Fillet a portion of an edge

    Also, if you would like a break out radius/cutter radius at the ending, you can sweep a triangle along a path... I do this probably once every 3 months or so, and it actually comes out looking nice and you can even dimension the runout radius.
  6. bhart

    Dimensioning a Radius Groove?????

    quest4k, Did you try a section, it should be able to pick up an arc then?
  7. bhart

    Master/Slave Master Cylinder

    kcj, Your suggestion is exactly what we had worked up and pursued for a couple of days, but then realized that packaging to the master cylinder would then also be and issue. We've decided to manufacutre our own master cylinder to eliminate packaging uncertainties. Thank you for your suggestions.
  8. bhart

    Master/Slave Master Cylinder

    Have been searching the internet all day for something that I was sure would exist: an electronically actuated master cylinder. For my system, I have a slave (output) cylinder that is mounted remotely in a very tight space, so no room for using direct electrical actuation on the output...
  9. bhart

    Piezo Contact Sensor

    We currently use an MSI laminated piezo film strip sandwiched between a cover plate and the vehicle to detect contact between a given surface of the vehicle and anything else in its surroundings (MSI P/N 1-1002405-0). We have a new project that requires a smaller sensor. Basically, the...
  10. bhart

    Trailing Link Flexure

    Greg, The part # would be greatly appreciated.
  11. bhart

    Trailing Link Flexure

    Norm, I see what you are saying about the 3DOF requirement, but the way that I have analyzed a trailing link in the past is to say... OK we have two points with a fixed distance in between them, one is grounded (chassis pivot) so what do we have to specify to determine where the other point...
  12. bhart

    Trailing Link Flexure

    Norm, No street use, strictly a race vehicle. Also, not looking for something that is "less harsh" or anything like that. I just mainly want to eliminate friction surfaces from the suspension system by eliminating sliding pivots. A similar idea to what open wheel cars (F1, Indy, etc.)...
  13. bhart

    Trailing Link Flexure

    Does anybody know of current designs that utilize a/multiple flexure joints as a substitute for a spherical type joint? I have been considering ways to accomplish this for the purposes of a racing suspension, where it is generally required that a trailing link joint be very stiff along the axis...
  14. bhart

    SURFACING / KNIT SURFACE QUESTION

    This is not the only reason, but if you try to fillet unknit faces SW informs you: "Cannont knit laminar faces". But if you knit them, it understands how to create the fillet. I'm not very experienced w/ surfacing, but I would imagine that there are other examples of similar operations in SW...
  15. bhart

    Selecting Specific Temporary Axes

    Is there a way to determine which feature the temporary axis I am selecting belongs to (it seems length of the axis is a rough indicator, but not good enough sometimes)? I am concerned w/ selecting specific temporary axes b/c in a part w/ concentric features, I would like to associate as much...
See more

Part and Inventory Search

Back
Top