Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by AsHRITH S

  1. AsHRITH S

    Accordion Spring design

    Hello, Assume that I have bent a sheet metal of 0.1mm thick, 9.4mm height & 3mm width to form a "V" with an angle of say 20°. Now, definitely, I can have a spring action when I try to compress the top ends of "V" provided the material is elastic. Let's assume that the material is AISI 304. Now...
  2. AsHRITH S

    Accordion Spring design

    We have space constraint & this spring can serve our purpose well. It reduces assembly time in the end product. Have higher life expectancy. These kind of springs are available with only certain vendors worldwide and has to be imported. I want to develop this kind of spring in our place and use...
  3. AsHRITH S

    Accordion Spring design

    The spring to be used in one way starter clutch. The deflection isn't large. I am not getting how to start with calculations for the required load. We can achieve the required load by trial and error. But, I don't want to do that thing. I want to standardize the design procedure for this kind...
  4. AsHRITH S

    Accordion Spring design

    Here is the link for Accordion spring representative photograph. I am ataching this link since i am unable to upload the photograph because of a technical issue...
  5. AsHRITH S

    Accordion Spring design

    I am looking out for generalized design procedure for Accordion spring. I looked into the web a lot but couldn't find information regarding the same. It would be of great help if experts out there could guide me through the same.
  6. AsHRITH S

    How to choose Engineering materials smartly ?

    Thanks for the suggestions, it helped me a lot in selection of the material.
  7. AsHRITH S

    How to choose Engineering materials smartly ?

    I would like to know what are all the generic aspects that has to be taken into account while choosing materials? Specifically steels. There are thousands of material available in the market now with varying capabilities who's property vary from each other in one or the other way. So, how can i...
  8. AsHRITH S

    Rectangular flat compression spring

    The name of the spring is Accordion spring, it would be helpful if you could suggest where i can get access to its design procedure & calculations
  9. AsHRITH S

    One way roller starter clutch design.

    Thanks a lot Mr. BrianPetersen for the best explanation which i have ever read. I'll be looking forward for your continued support.
  10. AsHRITH S

    One way roller starter clutch design.

    Thanks for your concern BrainPetersen, I am aware that the reduction is so large during cranking at the ring gear of starter clutch, to quote the reduction is in the range of 15:1 to 20:1. By this it is clearly indicated that starter motor inertia will dominate the flywheel inertia and helps in...
  11. AsHRITH S

    One way roller starter clutch design.

    Yes,I did. I am looking on how to apply inertia relation into it so as to know inertial effect on its performance characteristics.
  12. AsHRITH S

    Rectangular flat compression spring

    Dear sir, Can you please let me know what those springs are technically called as?
  13. AsHRITH S

    Rectangular flat compression spring

    Thanks for your concern sir. I will work with information provided by you. Ill revert back to you in case if i have any queries.
  14. AsHRITH S

    One way roller starter clutch design.

    Hello all, I am looking for some inputs for designing ONE WAY STARTER CLUTCH for 2 Wheeler's. What are the resources that i can refer to carry on with design? Also,Is it a critical parameter which has to be addressed with deep understanding. In fact I am aware of how important inertia...
  15. AsHRITH S

    Rectangular flat compression spring

    Hello Everyone, I am looking for the design calculation for the type of spring which is shown in the attached link below. I am not sure about how to approach this kind of spring with a correct technical name. I also referred to the SAE spring manual, Unfortunately this type of spring calculation...
See more

Part and Inventory Search

Back
Top