Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by ADAG

  1. ADAG

    Vibration Damping Compound

    Soil, according to the drawings
  2. ADAG

    Vibration Damping Compound

    I think I will agree with MintJulep and hydtools that the best is to simply clean the gap and leave it empty. I would think tar is too rigid. Thank you all for your suggestions.
  3. ADAG

    Vibration Damping Compound

    I need to fill the 1" gap to isolate vibrations, reduce noise and protect the floor slab. This is an old installation, there used to some sort of elastomeric material in this gap, it has however dissapeared with the years and the gap is now full of dirt and debris. The contact material...
  4. ADAG

    Vibration Damping Compound

    Hello, I am looking for a vibration damping compound to be used to fill a 1" gap between a concrete dynamometer base and the surrounding floor slab. Any ideas on a product for this application? Thank you,
  5. ADAG

    Pressure tank installation

    Apparently Cycle Stop Valve is a brand name, is there a generic name for this type of valve or is this a patent protected sole source valve?
  6. ADAG

    Pressure tank installation

    Thanks valvecrazy, With that low 1 GPM flowrate to the pressure tank, am I not going to have my transfer pump running almost constantly?
  7. ADAG

    Pressure tank installation

    Thank you all for your comments, Itsmoked aswering your question, the storage and pressure tanks are pretty much level, being the latter seated maybe 3 ft higher. Valvecrazy, the cycle stop valve sounds good to me, and for my pumping capacity (around 30 gpm) not very expensive. Altough...
  8. ADAG

    Pressure tank installation

    Hello, I have the following situtation regarding the installation of a water pressure tank and I would like some advice: I have a well with a submersible pump, pumping water to two 1000 gls storage tanks adjacent to the well site. About 1100 feet away from here there is going to be a...
  9. ADAG

    Ventilation issues on cooling load calculations

    I am working on the design of a Constant volume, DX a/c system (cooling only)for a Government Office. For the cooling load calculation I am including a ventilation load of 15 CFM/person in occupied office areas. Now in this same building I also have a cafeteria room, to be used only by...
  10. ADAG

    LPG demand calculations

    Hello, I need to calculate the total demand of an LPG system of a building. Anybody has a link where the general procedure is explained. I have all the items requiring LPG (ovens, water heaters, dryers, washing machines) and their BTU/hr rate. LPG's calorific value which I understand is...
  11. ADAG

    Difference between a wet-pit sump pump and a submersible sump pump

    I see, so basically in the submersible the motor/pump are together in a housing and the whole thing goes inside the sump whereas in the wet-pit type motor and pump are separated. I would assume wet-pit tend to be used for higher capacities. Thank you!
  12. ADAG

    Difference between a wet-pit sump pump and a submersible sump pump

    Hello, can anyone explain me the difference between a wet-pit sump pump and a submersible sump pump. I have seen this difference established in an UFGS specs document but dont understand their difference. Thank you!
  13. ADAG

    Underground sawdust extraction system

    I am currently working on the design of a sawdust extraction system for a small industrial woodshop which must run underground. I am looking for ductwork suitable for this application. I have been recommended to use pvc-coated galvanized ductwork. However, I am concerned about the...
  14. ADAG

    Lagging Room Ventilation requirements

    Hello, I am looking for guidelines/requirements for the ventilation of a lagging room. The room is small (17 x 13 ft.) and will be used for wrapping A/C ducts with insulation and working on fiber glass ducts. Is a duct collector required for this application, or can it be a simple...
  15. ADAG

    Slurry Abrasion Response (SAR) Tests results

    Hello I am looking for a table comparing the Slurry Abrasion Response (SAR) test results (Procedure according to ASTM G75) for different steels. Any ideas where I can find this? Thanks,
See more

Part and Inventory Search

Back
Top