Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by abaqusian

  1. abaqusian

    Contour plot of nodal forces

    Hi, I have solved a simulation in Ansys APDL. Its a bending simulation. A model holded on a support , then subjected to bending. On the support contact region, i have extracted the nodal forces (Structural forces [F] on the out of plane direction [Y] ) Now, i have a list of nodes and their...
  2. abaqusian

    Which stress to look ?

    HI all, I would like to know in which cases, we should consider looking into Principal stresses and IN which case, we should look into Normal stress ? An example illustration would be very helpful. regards
  3. abaqusian

    Boundary Conditions for a Full model (unsymmetric model)

    Hi all, Coordinate system : x,y are in-plane direction. z is the out-of-plane axis (vertical axis) How to provide the boundary condition (constraining) for a full model , which is unsymmetric ? Which nodes to fix ? For example : For Quarter symmetry model : One node is fixed in x,y,z...
  4. abaqusian

    Creating finer mesh at center and outer coarse mesh in a solid box

    Assafwei, thanks for the input. I refer them.
  5. abaqusian

    Creating finer mesh at center and outer coarse mesh in a solid box

    Hi Assafwei, It was a great reply. Thankyou very much. Do you see any possible tutorial for the steps you have mentioned? I know it cannot be exactly same steps but any similar tutorial, could you recommend me? thanks again
  6. abaqusian

    Creating finer mesh at center and outer coarse mesh in a solid box

    @ Stanum : Thanks for the reply. I will check the reference.
  7. abaqusian

    Creating finer mesh at center and outer coarse mesh in a solid box

    Dear all, I am currently working in LS DYNA to do an impact simulation. Physically it's like droplet impingement on a solid plate. I do not know how to create a solid box with finer mesh at the centre of droplet impact and in other areas of solid box, a coarse mesh. I want to create this...
  8. abaqusian

    How to sketch a rheological model ?

    Hi, This might be a basic question for your level. I was asked to draw rheological models like kelvin voigt / maxwell model in the microsoft word instead of just copying and pasting. I searched some but i was unable to find what I should be doing to draw a spring and a Damper (dashpot) and...
  9. abaqusian

    Help regarding Use of basic loop in matlab

    Additional information : Since, I work with large number of values (row wise) in Excel sheet in a single column , I want to multiply every 10 values in column1 with a factor , then next 10 values in column1 with an another factor And SO ON . I want to do this in a loop.
  10. abaqusian

    Help regarding Use of basic loop in matlab

    Hi everybody, At present, I am learning to work with matlab. I want to learn how to implement a basic loop for the following steps I perform. I have an excel file named "book" in format (.xlsx). I have two columns with ten rows each as shown below : serial value 1 0.15 2...
  11. abaqusian

    can you people help me ?

    HI, I am trying to learn to work on MATLAB by accessing the numerical data from an excel file. Kindly add your expert opinion. For example : in an excel file named "data.xls" , I have three columns: Column1 Column2 Column3 0.1 1000 20.05 0.2 1250...
  12. abaqusian

    Is it possible to run 2 to 3 simulation at a time in ANSYS batch mode ?

    Hi, I have some simulation to be run with changing (trial and error ) one parameter. First, i try with the one value and run in a ANSYS Batch mode. Then , I check results. Again, i change that parameter , then run for the second time same simulation with the new value for that parameter. My...
  13. abaqusian

    creating output graph for force vs crack length

    Hi, I have done a crack propagation simulation in abaqus through XFEM. There are two parts bonded together. A zone of crack/damage is created near the bonded area of two parts. The simulation ran properly and the crack propagates. Now , i would like to check the graph between the crack...
  14. abaqusian

    Need references for Failure / Damage Modeling with respect to Finite Element Analysis

    Hi, I am in need of references of books to learn about the Failure / Damage modeling with the application of it in the Finite Element Analysis. I would like to know about the recommended books or any other sites/articles etc ..., thanks
  15. abaqusian

    Need references for Failure / Damage Modeling with respect to Finite Element Analysis

    Hi, I am in need of references of books to learn about the Failure / Damage modeling with the application of it in the Finite Element Analysis. I would like to know about the recommended books or any other sites/articles etc ..., thanks
See more

Part and Inventory Search

Back
Top