Eng-Tips is the largest forum for Engineering Professionals on the Internet.

Members share and learn making Eng-Tips Forums the best source of engineering information on the Internet!

Register Log in
  • Congratulations dmapguru on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by AB53Mech

  1. AB53Mech

    Split Flange made from a forging?

    liko25, How much the ring thickness?
  2. AB53Mech

    Does design of lifting lug have some standard practice?

    '' pressure vessel handbook '' by Eugene F. Megyesy may help full too
  3. AB53Mech

    Shell with UG-34 (f) flat head extended as Skirt ASME Sec VIII Div-1

    Hi cak4engg, if you need to maintain minimum height for your design , then instead of extending Shell course is it possible for you to use Weld neck flange or long weld neck flange for item 4 ?
  4. AB53Mech

    PQR Responsibility

    agree with marty007 and other respected member's advice, please ask for partial data forms / U2 forms from head manufacturer vendor, this partial data form will need AI and vendors signature on it too. so as next step head manufacturer vendor will need to contact their AI , and that will...
  5. AB53Mech

    asme material receiving

    1st answer: please check your QC manual for 2nd answer: since you mentioned that '' because we are not going to use immediately.'' I would strongly recommend you to open each single plate and check it NOW it may be sound silly to other people whoever don't understand value of QC manual but...
  6. AB53Mech

    Pressure vessels in service

    Thank you metengr & Duwe6.
  7. AB53Mech

    Pressure vessels in service

    Hello , Members Generally , During Pressure Vessel fabrication we do NDE / NDT tests , Hydro tests etc. but how about testing on Pressure Vessels which are all ready in service ? how do we find defects on Vessels which are all ready in use or used ? can we check with NDE , Hydro tests same...
  8. AB53Mech

    Rated MDMT

    Thank you Tom & Marty for your detail helpful guidelines on it. - Yes , Marty , sorry for posting it in two different post about same question. next time I will keep it in my mind. Regards , - AB
  9. AB53Mech

    Rated MDMT

    - Thank you everyone for helpful guide lines on it . yes , I agree I really need to do some detail close CODE studies on it . Infect in general I am trying to read and study lot of times CODE with the help of CODE books , different books, online forums, I guess these are the way to get more...
  10. AB53Mech

    Rated MDMT

    Hello Respected Members , I am trying to run calculation in COMPRESS , for NPS18 Sch120 - SA-106 C smls pipe as cylinder and 2:1Ellip Head 1.25'' Thk SA-516 Gr.70 . Used MDMT is -20deg.F. Design Pressure 2500psi @350degF . So in result : In Deficiencies report, it gives me that one note : ''...
  11. AB53Mech

    Rated MDMT

    Hello Respected Members , I am trying to run calculation in COMPRESS , for NPS18 Sch120 - SA-106 C smls pipe as cylinder and 2:1Ellip Head 1.25'' Thk SA-516 Gr.70 . Used MDMT is -20deg.F. Design Pressure 2500psi @350degF . So in result : In Deficiencies report, it gives me that one note : ''...
  12. AB53Mech

    ASME Pressure Vessel Help

    Here I am attaching link for summarized document- '' A Brief Discussion for Div.1 , Div 2 ,Div 3'' for your detail reference . Regards , AB . http://www.absa.ca/faq/SectionVIIIcomparison.PDF
  13. AB53Mech

    National Board - stamped Vessels - Re rating , re certification -Procedures .

    Mr.Mike , Thank you for your advice . Regards , AB
  14. AB53Mech

    National Board - stamped Vessels - Re rating , re certification -Procedures .

    Respected Members , Need Guide lines : I need to verify / re calculate according to new pressure-temperature condition on few old manufactured Pressure Vessels ( Around 9 Pressure vessels like Interstate scrubber , suction scrubber , suction bottle , discharge bottle etc. ) I do have...
See more

Part and Inventory Search

Back
Top