ASME Training in Western Canada?
ASME Training in Western Canada?
(OP)
I am an EIT wanting to take an introduction to the practical use of the ASME codes (particularily Pressure Vessel codes). Can anyone recommend any good short course providers in Western Canada? (ie 3-7 days)
ANSI too if you know of any (flange design etc..)
ANSI too if you know of any (flange design etc..)





RE: ASME Training in Western Canada?
RE: ASME Training in Western Canada?
VIEW BROCHURE SECTION FOR DETAILS
http://ccs.goivytech.net/boiler_pressure/
Welcome to the Ivy Tech State College Boiler Pressure Vessel Training course scheduled for May 18 - May 30, 2003. I am the course manager and am here to answer any questions that you might have. If you have not already, you may want to go to our website at http://ccs.goivytech.net/boiler_pressure for more details on the course and what books you will need to bring with you. There is also information regarding hotels. The instructors (Dan Willis and Allan Clark) will be staying at the Hampton Inn here in Terre Haute and we recommend that students stay there also, if possible. We have reserved a block of rooms, with a special room rate, for this course, should you decide to stay at the Hampton. Evening study sessions and access to instructors tends to be more convenient. Be sure to let your travel agency know to advise the Hampton Inn that you are in the Boiler Pressure class
NOTE: 100 CLASS HOURS 10CEU
Leonard@thill.biz
www.thill.biz
RE: ASME Training in Western Canada?
RE: ASME Training in Western Canada?
RE: ASME Training in Western Canada?
chicopee (Mechanical)SEND ME E-MAIL TO Leonard@thill.biz
The below is the required CODE BOOK for the NBIC EXAM:
THE AMERICAN SOCIETY OF MEHANICAL ENGINEER’S:
ASME SECTION I RULES FOR CONSTRUCTION OF POWER BOILERS
ASME SECTION IV RULES FOR CONSTRUCTION OF HEARING BOILERS
ASME SECTION V NONDESTRUCTIVE EXAMINATION
ASME SECTION VIII RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIV. 1
ASME SECTION IX QUALIFICATION STANDARD FOR WELDIG AND BRAZING PROCEDURES, WELDERS, BRAZERS, AND WELDING AND BRAXZING OPERATORS
ASME B31.1-2001 POWER PIPING
National Boiler and Pressure Vessel Inspection (NBIC),
NOTE: 100 CLASS HOURS 10CEU
NEXT: NBIC EXAM JUNE 5, 6, 2003
Leonard@thill.biz
www.thill.biz
RE: ASME Training in Western Canada?
RE: ASME Training in Western Canada?
deanc - my email is cmesser@pris.ca
RE: ASME Training in Western Canada?
For training in Canada:
Codes and Standards Training Inc. (CASTI )
Suite 200
10544-106 Street
Edmonton AB T5H 2X6
Canada
Please note our correct telephone number is 780-424-2552.
http://www.casti.ca/
Leonard@thill.biz
www.thill.biz
RE: ASME Training in Western Canada?
RE: ASME Training in Western Canada?
RE: ASME Training in Western Canada?
I conduct personal and group training sessions with several pressure vessel engineering companies in the Edmonton and Calgary area.
The training seminars are primarily centered around the proper use of 'COMPRESS' pressure vessel design software.
I am an active user of 'COMPRESS' pressure vessel software.
If you would be interested in attending the next training seminar, send me your e-mail adress and I will send you an invitation.
Best wishes,
Warren
'wekeng@agt.net'
RE: ASME Training in Western Canada?
COMPRESS Training http://www.codeware.com/trainc6.html
Download the course brochure for more details (14 kb): TrainingC6.pdf click here
Codeware is pleased to announce that we will be offering training seminars in the use of COMPRESS for Pressure Vessel Design. Classes are currently one day sessions at our facilities in Houston, Texas. The seminar covers basic and advanced features of COMPRESS for Windows as well as general pressure vessel design principles. The course syllabus is flexible, based on participant level of experience, but see below for the general outline:
COMPRESS for Windows Training Syllabus
Instructors - Tom Barsh, P.E. and Mike Van Truong
I - Installation and Setup
II - Introduction to COMPRESS
III - Screen elements
IV - Using the Mouse in COMPRESS
V - Introducing the 3D screen graphic
VI - Setting up your defaults and user preferences
VII - Setting up a new design
VIII - Creating a new design
IX - Saving your new design
X - Opening an existing design file
XI - Running design calculations
XII - The design report
XIII - Printing your design
XIV - Saving your report
XV - Printing your design graphic
XVI - Using with Vessel Coster and Vessel Drafter
XVII - When Problems occur
XVIII - Updates to COMPRESS
XIX - Advanced Design Examples
Codeware has been reviewed and approved as an Authorized Provider by the International Association for Continuing Education and Training (IACET), 1620 I Street, NW, Suite 615, Washington, DC 20006. Codeware will award 0.8 CEU's to participants who successfully complete this program.
Here is a schedule of available training dates. We base these dates on customer feedback, so let us know what is most convenient for you.
Sign up now. Classes are filling quickly!
Fee is $350 per participant for the one-day COMPRESS class at the Houston facilities. Please call for group discounts. We will provide training computers, COMPRESS software, and lunch.
Contact John Migliavacca to sign up/for questions at 281-497-5705 or john@codeware.com
Leonard Stephen Thill
Leonard@thill.biz
www.thill.biz
RE: ASME Training in Western Canada?
gbuck.