×
INTELLIGENT WORK FORUMS
FOR ENGINEERING PROFESSIONALS

Log In

Come Join Us!

Are you an
Engineering professional?
Join Eng-Tips Forums!
  • Talk With Other Members
  • Be Notified Of Responses
    To Your Posts
  • Keyword Search
  • One-Click Access To Your
    Favorite Forums
  • Automated Signatures
    On Your Posts
  • Best Of All, It's Free!
  • Students Click Here

*Eng-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.

Posting Guidelines

Promoting, selling, recruiting, coursework and thesis posting is forbidden.

Students Click Here

Jobs

AC Frequency

AC Frequency

AC Frequency

(OP)
How would one increase the frequency of an AC signal?  I am looking into inductive heat treating and to my surprise the units are 10k dollars and up.  I am trying to go from 110v, 60 hz to 110v, ~10kHz.  Any ideas?  Thanks

RE: AC Frequency

Possibly, an audio amplifier driven from a function (sine wave) generator. Higher power is available in guitar amplifiers.

RE: AC Frequency

I would think RF would be a problem if you did that. Heat trace cable has no need to be shielded at this point, so I doubt it is available.

RE: AC Frequency

I built something like this for my university thesis, except mine was a current-source inverter fed on a diet of 415V 3 phase at 20kW and an ample supply of cooling water.

How much power are you trying to transfer into the load? Audio amps for the semi-pro market are readily available up to about 1kW into a small load. A coupling transformer might be needed to impedance match the load coil to the amplifier. They're fun to build, especially trying to get hold of small quantities of large section ferrites.
 

----------------------------------
  
Sometimes I wake up Grumpy.
Other times I just let her sleep!

RE: AC Frequency

I've just watched the youtube clip. That is disturbingly similar to the thing I built, but a lot smaller. The highlight of my project was getting over 7000 people evacuated from the engineering buildings one snowy November day - my birthday funnily enough - after smoke started pouring out of a cable duct. There was a big inquiry about why the breakers had not tripped but I wasn't privy to any of that.
 

RE: AC Frequency

(OP)
Very helpful info guys, thanks!  Im looking to heat a ~1" dia steel rod to only about 400 deg on the surface.  I dont think i need alot of power.  

RE: AC Frequency

If you are heating a conductor, (steel), can't you just run a current thru it?

Keith Cress
Flamin Systems, Inc.- http://www.flaminsystems.com

RE: AC Frequency

Ok, so the question is are you trying to achieve surface heating only or bulk heating? 10kHz suggests surface only in which case you need a powerful source to get energy into the surface layers faster than conduction can get it away from the surface into the core of the metal. Is this for a surface hardening application where you need a hard surface over a softer core? Also do you mean 400C or 400F? Big difference in power! I assume 400C for a metal hardening application.

BTW, have you considered adapting a bearing heater?

'Smoked,

My project was notorious enough before this incident: setting the university on fire elevated me to demigod status.
 

----------------------------------
  
Sometimes I wake up Grumpy.
Other times I just let her sleep!

RE: AC Frequency

You are not alone Scotty!

There is a commissioning engineer at ABB. He is named Smokey after he burned down a paper mill in Israel. He is also quite famous.

Gunnar Englund
www.gke.org
--------------------------------------
100 % recycled posting: Electrons, ideas, finger-tips have been used over and over again...

Red Flag This Post

Please let us know here why this post is inappropriate. Reasons such as off-topic, duplicates, flames, illegal, vulgar, or students posting their homework.

Red Flag Submitted

Thank you for helping keep Eng-Tips Forums free from inappropriate posts.
The Eng-Tips staff will check this out and take appropriate action.

Reply To This Thread

Posting in the Eng-Tips forums is a member-only feature.

Click Here to join Eng-Tips and talk with other members!


Resources