×
INTELLIGENT WORK FORUMS
FOR ENGINEERING PROFESSIONALS

Log In

Come Join Us!

Are you an
Engineering professional?
Join Eng-Tips Forums!
  • Talk With Other Members
  • Be Notified Of Responses
    To Your Posts
  • Keyword Search
  • One-Click Access To Your
    Favorite Forums
  • Automated Signatures
    On Your Posts
  • Best Of All, It's Free!
  • Students Click Here

*Eng-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.

Posting Guidelines

Promoting, selling, recruiting, coursework and thesis posting is forbidden.

Students Click Here

Jobs

Oil levels

Oil levels

Oil levels

(OP)
The company I work with which has mostly EMD 16 cylinder and Fairbank Morse 8 cylinder engines, has a habit of keeping the oil level low in effort to burn less lubrication oil.
I hate the idea. They seem to keep the oil on the add mark of even a bit under then just add 20 to 40 liters.
I am a 4th class and new there so I cant say anything but I think that it is wrong.
On the dip stick there is a add mark and a full mark and I would keep it  on the full mark.
I am quite sure the engineer already compensated for waves of the seas.
I don't doubt that the engines burn more oil when kept up in level, but I think that is the amount they burn and lowering the level in the oil pan is just compensating for poor oil control rings.
I would like to hear what anybody has to say.

RE: Oil levels

The person who put the marks on the dipstick generally has vastly more knowledge than the chief or super wishing to cut oil consumption.

In my experience it is true that oil consumption is less when running at lower levels. There is an interesting paper on the economics of this practice that I can't at the moment lay my hands on.

I have sailed as chief opposite a swing into this practice. The oil consumption at the end of swings was not that significant and the oil quality with lower sump levels was significantly worse. All major parameters from oil analysis were much worse - particulary particulates, viscosity and consumables.

My philosophy is to run machines within there designed operating limit! If you arn't making a dollar by running the business as it should be then get out...   

RE: Oil levels

The engine - any engine - should work perfectly at any oil level between the minimum and maximum marks on the dipstick. The practice of using the minimum mark and adding '20 to 40 litres' doesn't seem to be an irresponsible act (unless that over-fills it).
The minimum mark (asuming it's a proper marine diesel) will have been calculated to accommodate the worst scenario of hull roll, pitch and slosh (maybe 40 deg - depends on type of craft).
The normal practice of filling to 'max' gives you a margin for reduction of oil level due to burn, and is therefore good for peace of mind. If you can be sure that the level is always 1 mm over the minimum mark, you should be just fine. 1 mm under, and you're in trouble. Engine manufacturers know what they're doing.

RE: Oil levels

Hey Frankie, what crankcase vacuum are you running on your EMD Engines?

RE: Oil levels

(OP)
On the Fairbanks Morse I remember checking the inches of water and compared it with the manual and it was within spec.
The EMD's on the other ship do not have a manometer on the engines and I do not know what the vacuum is.
I just got a letter today that I have been accepted at a power plant generating station so I guess I will never see  those particular engines again and I don't have to think about it.
Thanks for the replies

RE: Oil levels

Congratulations frankiee
Yours
Bill

Red Flag This Post

Please let us know here why this post is inappropriate. Reasons such as off-topic, duplicates, flames, illegal, vulgar, or students posting their homework.

Red Flag Submitted

Thank you for helping keep Eng-Tips Forums free from inappropriate posts.
The Eng-Tips staff will check this out and take appropriate action.

Reply To This Thread

Posting in the Eng-Tips forums is a member-only feature.

Click Here to join Eng-Tips and talk with other members!


Resources