INTELLIGENT WORK FORUMS
FOR ENGINEERING PROFESSIONALS
Log In
Come Join Us!
Are you an
Engineering professional?
Join Eng-Tips Forums!
- Talk With Other Members
- Be Notified Of Responses
To Your Posts
- Keyword Search
- One-Click Access To Your
Favorite Forums
- Automated Signatures
On Your Posts
- Best Of All, It's Free!
- Students Click Here
*Eng-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.
Posting Guidelines
Promoting, selling, recruiting, coursework and thesis posting is forbidden. Students Click Here
|
Home
Advanced SearchYou are in the site-wide keyword search. If you'd like to search a particular forum, navigate to that forum and click on the "Search" button in the gray navigation bar.
|
839 records matched your query of equipment pad. Outputting records 1 to 20.
... very shallow to the soil to me the pad and the equipment can be thrown the air together during... ...that is because you only calc the seismic load using the weight of the equipment. if the pad just... ... suggestions? The equipment going on the pad will weigh about 2,500 pounds.... ...I have an existing 5' X 10' X 4" pad that is too small. I don't want to have to chip it up to pour... ...I am checking the concrete pad design for a piece of equipment (i.e. small commercial chiller w/ 70... ..., since this is a piece of "equipment"? For example, vibrations, impact loads on the pad, heavy... ... of an equipment pad that will be installed outdoors? The pad I am designing needs to be at least 8" thick... ... depth. The pad is about 8' x 10' in plan size. Normal depth of footing around here to prevent frost... ...I am an EIT with a question about concrete pad design for heavy equipment such as generators, HVAC... ...The pad should be bigger than the equipment and thick enough to anchor into. Beyond that, some... ...I have been unable to find any information on equipment pad design. I was interested in knowing... ...Common factors affecting equipment pad design approaches: equipment size, type & intensity of loads... ... between the equipment pad and the embedded rebar.
This is not typical.
My guess is you just have... ... some piece of equipment that needs a pad so that it sits elevated from the slab. In that case... ...Does anyone know of a word that means "above grade height" for a pad, or is that pretty much... ...All of the code references that I'm seeing are along the lines of "Equipment must be X inches above... ... equipment loads. This is a very large existing pad (approximately 1300SF) that will support multiple new... ... pieces of equipment (some permanently anchored to the pad and some movable on wheels). This pad sits... ...I have an existing 9'x18' concrete equipment pad reinforced with #4s @24" oc both directions on 4... ..." of 3/4" clean crushed rock with no fines with 3 pieces of equipment on it. I will be adding 2 pieces... ... have been looking for examples of how to design an equipment pad that will be installed on an existing... ... installed many such equipment pads but I was not involved with the design. I expect for the new pad I... ...Where would I look to find out the effects of liquid nitrogen on an existing concrete pad? Has... ... it occur in a critical area or just on a non structural pad?
If you had a spill I would recommend some... ... lbs. for the tank, equipment, and pad. Add about 57,000 lbs. for liquid when filled.
How can I work... ...Now, this is out of my area of expertise so bear with me. I want to install a 22" concrete pad over... ...We have primary utility service and a 25kV-480Y/277V outdoor located pad-mounted transformer... ... that concerns me is that we have the green equipment grounding conductors connected between the switchgear... ... piece of equipment?
Do utilities anchor transformers to their concrete pads?
... ... specific way.
We had a reason we did what we did, as the concrete pad wasn't wide enough to do... ... water in conduit do not get to the expensive equipment.
As for avoiding flood at the pad, seek advise... ... on transformer pad
Be Safe.... ... with the 2 hole pad. My concern is, when dealing with equipment rated at 1200 amps the connection is commonly... ... hole Pads and I will be connecting to these C.T.’s with double 500 MCM to Nema 4 hole pad terminal... ... that will store a large RV, boat, tractor, and other heavy equipment.
The slab foundation is a 40' x 50... ... bolts.
With the contractor checked the pad location with a lazer level, we discovered that the end... ...?
I was considering only adding dowels at the edge of the new equipment pad making the concrete per... ... and that the equipment pad is just filler, like a housekeeping pad. i.e. no horizontal shear transfer between upper... ... nozzle being added to the pressure vessel when brand new equipment was installed on site and required... ...A reinforcing pad around a nozzle plays a critical role in reinforcing the opening. The Re-Pad... SEARCH AGAIN
|
Resources
What is rapid injection molding? For engineers working with tight product design timelines, rapid injection molding can be a critical tool for prototyping and testing functional models. Download NowThe world has changed considerably since the 1980s, when CAD first started displacing drafting tables. Download NowPrototyping has always been a critical part of product development. Download NowAs the cloud is increasingly adopted for product development, questions remain as to just how cloud software tools compare to on-premise solutions. Download Now
|
|
