INTELLIGENT WORK FORUMS FOR ENGINEERING PROFESSIONALS
Log In
Come Join Us!
Are you an Engineering professional? Join Eng-Tips Forums!
- Talk With Other Members
- Be Notified Of Responses
To Your Posts
- Keyword Search
- One-Click Access To Your
Favorite Forums
- Automated Signatures
On Your Posts
- Best Of All, It's Free!
- Students Click Here
*Eng-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.
Posting Guidelines
Promoting, selling, recruiting, coursework and thesis posting is forbidden. Students Click Here
|
Home
Advanced SearchYou are in the site-wide keyword search. If you'd like to search a particular forum, navigate to that forum and click on the "Search" button in the gray navigation bar.
|
61 records matched your query of clad vessel PWHT. Outputting records 1 to 20.
...I have a vertical carbon steel vessel, 7/8" thick. Bottom portion is internally integrally clad... ... with 317 SS. I interpret UCL-34(b) as all clad vessels are to be PWHT unless clad with 405 or 410S. Can...
... or vessel must go to furnace without these nozzles and shall be locally pwht after furnace?in this case... ... will be attached by welding buttered with Inconel 82 or 182, PWHT the vessel and then install the solid nozzles...
... to carbon steel and that no PWHT need be performed for the vessel in lethal service. I believe the intent... ... the vessel from the PWHT requirement of UW-2(a). The reply, however, refers the reader to UCL-34, perhaps...
...engineermat;
Is the vessel being fabricated under UCL or UCS? The reason for my asking... ... is that different rules apply for carbon steel substrate construction and weld overlay versus an integrally clad...
...1. PWHT is not a requirement for the clad/overlay itself. Hence for a clad component (with any cs... ... of PWHT for the overlay or the weld procedures used for the overlay. 3. However if one clad component...
... not clad or shall we PWHT the vessel as a whole, clad and unclad C.S. plates?
An answer would... ...The vessel is an Amine regenerator. The code requires to PWHT non-clad carbon steel plates between...
... vessels and other components that have been clad and subsequently PWHT with no ill affects on the clad... ...For a thick wall vessel, PWHT can be many hours. I personally follow the pointer that used...
..., the above applies as well, but simulated PWHT must be performed on vessel materials on the total number... ... of cycles of PWHT the vessel will see, often including extras for field repair (usually required by customer...
...I have a vessel constructed of A516 gr 70 clad with 316L Stainless Steel in accordance with [b]ASME... ... section VIII[/b] and my question is related to the [b]welding of clad material[/b]. I do not have very...
... treated vessel. PWHT after linnig installation would not be possible.
... ...Thank You SJones and PAN.
Yes the vessel was designed per ASME VIII Div.1 but PWHT was not a...
...http://www.eng-tips.com/search.cfm?q=clad+vessel+PWHT&action=search
Steve Jones
Corrosion... ...Dear All
I have a problem with the PWHT of a vessel when it comes to its overlay.
[quote ASME...
... be PWHT and subsequently clad, if permitted.
2. The nominal thickness that governs PWHT for the vessel... ... is following:
Cr/Mo vessel with SS cladding. Shell roll-cladded, flanges overlayed.
The PWHT time should...
..., and NO PWHT.
If the shell segments already have been clad and now you are going to weld the shell segments... ... the vessel welds using Inconel weld metal – again no PWHT would be required only a 200 deg F preheat.
...
... to be installed to a clad section (CS+316L SS)
The vessel requires PWHT.
Can I strip off the clad where... ..., then perform PWHT for the entire vessel. After PWHT, weld the 316LSS support ring to the buttered layer...
... (P-4) and clad with SA-240-321 ( P-8). PWHT is required. Would it be permitted to weld a... ... circumferential ring to the clad after PWHT?
After reviewing the requirements of UW-40, Table UCS-56 for P-4...
... to withstand the minimum 3 cycles PWHT to prove that the SS clad will not be subjected to sensitization?
2... .... Production Coupons:
2.1 If the vessel requires no PWHT, the test coupons are only required to be tested...
... relevant NDE for wet sour service vessel is WFMT on all internal welds after PWHT.
... ... ferritic type alloys after clad restoration may be somewhat high w/o PWHT. Regarding austenitic clad...
... life of the vessel... etc
-Thicker clad , more money.http://www.eng-tips.com/viewthread.cfm?qid=408590... ... attachment for guidance.
-Many parts in a clad pressure vessel, e.g nozzles, fittings, Dished Heads...
... on how the clad components would get manufactured including the required PWHT.
It's FYI a lot clad... ... withstand Normalizing at Dishend and PWHT after completion of full vessel.
As per KOC spec Explosion...
... , should vessel to be subjected to PWHT?
if yes, doesn't it any harmful effect on inconel weldedoverlay... ... of nozzle to shell pwht is mandatory. In this case does PWHT have any harmful effect on cladded vessel...
SEARCH AGAIN
|
Resources
What is rapid injection molding? For engineers working with tight product design timelines, rapid injection molding can be a critical tool for prototyping and testing functional models. Download Now
The world has changed considerably since the 1980s, when CAD first started displacing drafting tables. Download Now
Prototyping has always been a critical part of product development. Download Now
As the cloud is increasingly adopted for product development, questions remain as to just how cloud software tools compare to on-premise solutions. Download Now
|
|