INTELLIGENT WORK FORUMS
FOR ENGINEERING PROFESSIONALS
Log In
Come Join Us!
Are you an
Engineering professional?
Join Eng-Tips Forums!
- Talk With Other Members
- Be Notified Of Responses
To Your Posts
- Keyword Search
- One-Click Access To Your
Favorite Forums
- Automated Signatures
On Your Posts
- Best Of All, It's Free!
- Students Click Here
*Eng-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.
Posting Guidelines
Promoting, selling, recruiting, coursework and thesis posting is forbidden. Students Click Here
|
Home
Advanced SearchYou are in the site-wide keyword search. If you'd like to search a particular forum, navigate to that forum and click on the "Search" button in the gray navigation bar.
|
20 records matched your query of anchor pipe steep slope. Outputting records 1 to 20.
...How do you calculate the size and spacing of concrete anchors along a buried pipe with a steep... ... slope? I've looked at other sites and have not been able to find a good example of an anchor design... ... that have been presented. Given the steep slope, smooth pipe and limiting capacity due to the inlet... ... is not a constant slope, local low points can have a lot to say about maximum pressures.
If your pipe can... ... of a steep slope. Runoff flows from the pipe (elev=180 feet), down the slope, and ends at a salmon... .... But with the 180 feet I am not sure. How are you going to anchor the pipe into the slope, 10' rails... ... should be able to have no anchor blocks. Even at 40 % slope, soil friction will hold the pipe in place... ... an achor block is required. The pipeline that we are designing is an underground carbon steel pipe, which... ... than No. 11. However at a flatter slope but with the same support reaction the horizontal component... ... angle to the bottom of deck slope. Total area of this shear plane is about 180 long x 22 inches through... ... concrete collar placed around the pipe to minimize groundwater flows in the backfill and bedding of steep... ... also do the trick. However, if they are to anchor the pipe to prevent it from sliding downward... ... the pipe, power wire, and safety cable are not necessarily tightly clustered or even in the center of the 6... ....
Can you drop a smallbore pipe down the hole? 500 ft of even smallbore pipe is going to weigh some... ... not exceed a 10% slope for pipes. On steep slopes, I would anchor the pipe into the slope.... ... special design considerations for design of such a steep pipe. My biggest concern is the potential... ...-tensioning would give rise to some high tensile stresses in the vicinity of the anchor.
Dik... ... tensile stresses in the vicinity of the anchor.[/quote]
Yes the stresses would be fairly intense... ... at a initial 200' run of pipe at a 4% slope, with a slope of 11% to 15% in the remainder of the pipe... ... could have a full pipe at the start but 2 phase flow as the slope increases. Could get some vibration... ... slope and also as energy dissipation.
you can slope the pipe but then you need to anchor the pipe... ... for the pipe coming in. This will create a pipe with a slope of approx 5% to the manhole at bottom of slope... ... held a backhoe on a cable attached to two dozers and trenched, then lowered the pipe as above. Slope... ...Due to various restrictions, I'm looking into running a 8" water line up a 85% slope. The line... ...The FHWA puts it in terms of hazard and risk. If you've got a steep, granular slope above a wooded... ...I need to determine a safe slope for a very stiff clay (Unconfined Compressive Strength - 4 tons... ... was originally designed as an SRW type wall. It is near the bottom of steep slope and in front of a river. Thus... ... there are relatively long grid lengths. It varies in height up to maybe 14' tall and the slope is about a 1V:1.5H or 1V... ... steep slopes maxing out between 20 and 25%. Any information on anchor block design and how often... ... don't know all details of steep slope pipeline construction, I believe a sort of "stair-step" sort... ...' high) with way too steep of a slope. I originally designed a drop inlet structure before the wall... ... to the wall, anchor to the pipe upstream of the wall,or cast a "dead man footing" to take the thrust force... ...I'm looking for references to design anchor blocks below the bell end of a pipe on a steep slope. ... ...
Guideline for the Design of Buried Steel Pipe - July 2001
This guideline presents design provisions... ... representation creates slippery slope.
Today too few women, tomorrow too many Jews, what's next?
[color... .... They discuss the impressive accomplishments each of them made despite the steep uphill climb not required... ...If you are using a concrete 'collar' for the anti seep dams and anchor them to the pipe... ..., it will also help keep the mainline in the same position on the hill. Like using an anchor to hold the pipe up... ... or operation. Most existing services will have rights extending 3m or more from the pipe outer edge... ... of other services ( especially overhead wires) and ease of draining or venting the diverted pipe of its... SEARCH AGAIN
|
Resources
What is rapid injection molding? For engineers working with tight product design timelines, rapid injection molding can be a critical tool for prototyping and testing functional models. Download NowThe world has changed considerably since the 1980s, when CAD first started displacing drafting tables. Download NowPrototyping has always been a critical part of product development. Download NowAs the cloud is increasingly adopted for product development, questions remain as to just how cloud software tools compare to on-premise solutions. Download Now
|
|
