INTELLIGENT WORK FORUMS
FOR ENGINEERING PROFESSIONALS
Log In
Come Join Us!
Are you an
Engineering professional?
Join Eng-Tips Forums!
- Talk With Other Members
- Be Notified Of Responses
To Your Posts
- Keyword Search
- One-Click Access To Your
Favorite Forums
- Automated Signatures
On Your Posts
- Best Of All, It's Free!
- Students Click Here
*Eng-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.
Posting Guidelines
Promoting, selling, recruiting, coursework and thesis posting is forbidden. Students Click Here
|
|
111 records matched your query of second nut. Outputting records 1 to 20.
...You could use a jam nut which is a second nut tightened against the first. Nuts made... ... where you want it, put on the second nut till it touches the first. Hold the first nut with one wrench... ... to loosen the bottom nut is by turning the stud. My second photo, in the 5 o'clock position, you can see... ... is to remove the bottom nut and pull the stud out from the top. We cannot go down because there is no clearance... ... and the plate. On the other side of the plate, I have a hex nut on the screw with a delrin thrust washer between... ... the nut and the plate. I just snug the nut down to take up any axial play in the screw & when I install... ...With traditional threads (UNF/UNC), you sometimes install a second nut behind the first nut to lock... ...I agree with Mike, I don't think it's practical to use a 'second' acme 'nut' to jam another one... .... Second, there is likely sufficient excessive bearing stress at the misaligned nut/washer/flange contact... ... tapered. Of the 80 bolts, 6 exhibit a gap between the nut and the washer at one extreme of the nut... ..., where after the failure the tie rod fragment along with the nut shoot away from the base with some... ... decent speed. They welded in restraints meant to stop the fragment/nut, but are now questioning whether... ... always has an axial load on it.
If there were problems I suppose a second nut could be used, i.e... ...., after adjustment, the second nut can be tightened down into the first nut for a locking effect... ... to perform very well, especially if your motor is small. Turning a 3/4" allthread shaft in a nut with any... ... nut. You can get a 3/8-10 pair from McMonkey-Carr for about fifty bucks.
There are lots of ways... ...
I have a 1/4 x 16 Acme thread (1/16" lead) .... if an acme nut on this rod hits a stop, the nut... ... will jam and lock against the stop.
I have a 1/4 X 1" Lead Screw (1" lead) ... if a leadscrew nut... ... is that the field technician must back up the nut against the insulator with a second wrench when tightening the jam... ..." copper threaded rod through a panel with a nut and jam nut on both sides containing the rod. one of nuts... ...Thank you,btrueblood and drawoh,I want to measure the tightening torque of the nut in real time... ... and the temperature cycle make the nut loose and I need to find out how loose it is after a period of service.
I... ... for the dimensional input values? The shaft has a M6x0.75 external thread and a nut is used to press and hold the hub... ... to the shaft. My end goal is to calculate the required torque on the nut to provide the calculated required... ... best to make sure that there was no anti seize between the end of the lug nut (part that seats... ... they are too rusted. However, just because the lug nut came off with an impact does not mean that the stud... ... that occurred to me…
1. Presently, I have an adjustment nut at one end of the two springs which... ... use the adjustment nut at the end of one spring to initially make the lever vertical at neutral before... ... is shaped like an hour glass or a pear it won't perform like you expect it to. Second, get access to a pull... ... a regular nut inside.
-Mold the part with a hex pocket on each side. Leave nut on the jacking screw... ... (installed first), and the heavy nut (installed second) is pushing against the jam nut from the other side... ..., into the bolt thread. Therefore the heavy nut, installed second, needs twice the amount of thread strength... ... to fit the head of the torque wrench on the nut (the bolt head is head by the tooth casting). I have... ...First of all, I don't think you mean 300 ft lb on a bolt.
Second, in order to torque up... ...). The lead screw is a 5/16-18 B7 All Thread and the torque wrench was turning a 5/16-18 hex nut at the end... ... the equivalent of the 20 ft-lbs of torque form the lead screw and nut. I hope this makes sense and someone can... ... have a lot to begin with. And the second problem is.. unless it's a jet nut or something small, I wont... ... steel nut? If you have clearance limitations on the back, can you use a flat-head screw in a countersunk... ...I have a threaded stem nut that drives a valve shaft up and down. The threads on the stem nut have... ... are. The steel valve stem is threaded, the bronze stem nut threads over the threads on the valve stem and has... SEARCH AGAIN
|
Resources
What is rapid injection molding? For engineers working with tight product design timelines, rapid injection molding can be a critical tool for prototyping and testing functional models. Download NowThe world has changed considerably since the 1980s, when CAD first started displacing drafting tables. Download NowPrototyping has always been a critical part of product development. Download NowAs the cloud is increasingly adopted for product development, questions remain as to just how cloud software tools compare to on-premise solutions. Download Now
|
|
