INTELLIGENT WORK FORUMS
FOR ENGINEERING PROFESSIONALS
Log In
Come Join Us!
Are you an
Engineering professional?
Join Eng-Tips Forums!
- Talk With Other Members
- Be Notified Of Responses
To Your Posts
- Keyword Search
- One-Click Access To Your
Favorite Forums
- Automated Signatures
On Your Posts
- Best Of All, It's Free!
- Students Click Here
*Eng-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.
Posting Guidelines
Promoting, selling, recruiting, coursework and thesis posting is forbidden. Students Click Here
|
|
74 records matched your query of double nut. Outputting records 1 to 20.
...% will be good, 15% will be too tight, and 5% will be too loose.
I would also steer away from the double nut... ... AND suspenders approach you could double-nut it with a standard nut.
ISZ
... ... these mothers off then I would replace them with longer studs so that you can double nut the top nut to give you... ... is to remove the bottom nut and pull the stud out from the top. We cannot go down because there is no clearance... ... and the plate. On the other side of the plate, I have a hex nut on the screw with a delrin thrust washer between... ... the nut and the plate. I just snug the nut down to take up any axial play in the screw & when I install... ...I am designing a lead screw assembly with a stationary, vertical screw and a moving nut in a nut... ... out is how to calculate the resultant torque on the nut (due to friction), ie the reaction torque... ... double the clamp load.
The ISO nut heights are designed so that you will get bolt breakage at least 10... ... on the nut when reaching close to max torque value.
The bolt is a class 10.8 and the nut is class 10, to my... ...://www.eng-tips.com/search.cfm?pid=404&action=Search&q=double+nut]double nutting[/link]/[link http://www.eng... ....
I think the double-nut would work, but don't know if the acme thread would behave the same... ...Get rid of the jamb nut. It is double redundant, and worse, it puts a pin,shear load on the copper... .... This situation is indeed removing the human element. And a double jam nut is probably the way to go. I was really... ... best to make sure that there was no anti seize between the end of the lug nut (part that seats... ... they are too rusted. However, just because the lug nut came off with an impact does not mean that the stud... ...Hi Guys,
I have a couple of questions regarding a double taper bearing for trailer axle... ... the castellated retaining nut. In the past, I had always been told to tighten the nut as tight as I can with my... ... and or shouyld they be tack welded or double nutted?
Does anyone know of others that use stud mounted fan... ...With the rotation and vibration be enough incentive.
Should they be tak welded or double nutted?... ...i imagine that its working like a double nut situation ... when you put 2 nuts on a bolt, the inner... ... double nut.
And I could make it truly bottom out, where the end of the bolt contacts the cap part... ... for the dimensional input values? The shaft has a M6x0.75 external thread and a nut is used to press and hold the hub... ... to the shaft. My end goal is to calculate the required torque on the nut to provide the calculated required... ... it was before. When the rollers are in contact with the cam and a load is applied, this seems to double... ... that occurred to me…
1. Presently, I have an adjustment nut at one end of the two springs which... ..., that would perhaps explain it.
In which case, if I double the width of the lead nut will that not halve... ...I've a short bar of teflon and made a 15mm wide lead nut for a M12 steel rod (standard thread... ..."I torque the stud with out anything assembled"
So you are winding a nut down until it jams... ... double and hence yes failure will ensue.
Find out of any lubricant is getting on the threads at assembly... ... the nut on the end of the bolt coming loose, I would recommend locking the nut.... ... the difference, nor do its users. With the large loads I would try hard to put those pins in double shear, make... ...I have a threaded stem nut that drives a valve shaft up and down. The threads on the stem nut have... ...i think you mean that the tip of the threads has been worn off. i don't think this would double... ...I have an application where a component is positioned using a nut tightened onto a threaded rod... ... via the position of the nut on the threaded rod.
The application is prone to high ambient... ...Cryogenically treat the nut and the threads if wear is a problem. It should double or triple... ....
I am looking at the trade-offs between using a ball-screw, ACME threaded rod with ACME nut or UNC... ... an nylon insert on a nut.
Contaminates on the bolt don't significantly change the performance of a nylon... ... will probably put the nylon nut back on. He probably won't clean and reapply loctite.
Loctite... SEARCH AGAIN
|
Resources
What is rapid injection molding? For engineers working with tight product design timelines, rapid injection molding can be a critical tool for prototyping and testing functional models. Download NowThe world has changed considerably since the 1980s, when CAD first started displacing drafting tables. Download NowPrototyping has always been a critical part of product development. Download NowAs the cloud is increasingly adopted for product development, questions remain as to just how cloud software tools compare to on-premise solutions. Download Now
|
|
