INTELLIGENT WORK FORUMS
FOR ENGINEERING PROFESSIONALS
Log In
Come Join Us!
Are you an
Engineering professional?
Join Eng-Tips Forums!
- Talk With Other Members
- Be Notified Of Responses
To Your Posts
- Keyword Search
- One-Click Access To Your
Favorite Forums
- Automated Signatures
On Your Posts
- Best Of All, It's Free!
- Students Click Here
*Eng-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.
Posting Guidelines
Promoting, selling, recruiting, coursework and thesis posting is forbidden. Students Click Here
|
|
150 records matched your query of force main. Outputting records 1 to 20.
...I have an unusual problem. I am designing a 10 MGD Lift Station and 30” DIP Force Main... ... that is pumping downhill. I am a licensed engineer and experienced in pipeline design, but pumps and force main... ...The existing condition is a 4 inch dia. ductile iron sanitary sewage force main with 20" to 24... ... 500 foot long force main. Standard cover to be below frost lines in our area (New Jersey) is 48"... ...Has anyone come across a case where a new force main is tied into an existing force main? I've got... ... a development situation where a residential lift station feeds a 6" force main, which then passes... ...We are proposing to connect a 4" force main to an existing 14" force main. Based on old design... ... plans, the 14" force main is operating at 1,600 GPM @ 216' TDH (two submersible 130 HP pumps). Our... ...I am trying to assess the condition of a 24" DIP sewer force main. There have been previous... ... about stray current is interesting however. The DIP force main is in a power line right of way... ...Existing 6 inch force main ties into manhole . From that manhole there is a 8 inch gravity sewer... ... residential into force main…with sanitary sweep at like 2:00 maybe even into top of force main….at about... ... him to tie into a force main owned by the school district that I represent. We have determined... ... that the force main has capacity to handle the additional load. The question is, is it possible to tie directly... ...Good practice is to design your force main to have NO low points so that cleanouts, or scour valves... ... and restrict flow through the force main. It is recommended that a clean-out or blowoff be provided at low... ..., and also size the force main. A pump station handles 62.84 gpm downstream, but I need to figure what... ..., or diameter. I am assuming the force main is Class 52 DI pipe. ... ...thread161-237329 I've read this thread on the problem with force main blockage and have... ... tank in the pump room. If you are feeding bioxide (Calcium Nitrate) into a long force main... ...Need to use a 3-inch force main, almost 3 miles long. SDR 21 comes in 3-inch but obviously... ..., say, "The minimum force main diameter for raw wastewater shall not be less than 4 inches (100 mm)"?
... ... proposed industrial park. The 4-inch force main will be used mainly for a couple of small subdivisions. I... ... about sewage staying in the lines too long. The force main is about 22,000 feet long and they don't... ...
Hi,
I have a project wherein I have to extend an existing sewer force Main (which... ... is connected to a gravity sewer)to a new location. The force main backs up whenever it tries to discharge raw... ...I have an existing (in-place) pipe that must be used as a casing for a new force main... ... of the casing in order to get the force main back up to workable grade, where the pipe laying would continue... ... flow, so if you put it downstream of a pump, the force main would go to gravity flow at the comminutor... ... and the pump would have no effect on the downstream force main.
I suppose you could design a comminutor... ... to serve the new building and tie into an existing 2" force main that serves the adjacent business... ... the existing pump). Very low flows and very flat topography along the force main to the discharge point. I... ... of force main with about 10 interconnections between force mains. Site has almost flat terrain... ... and will discharge into a large force main with a standing pressure of about 50 feet... ...A transient analysis of a municipal raw sewage force main highlighted a need to employ mitigation... ...stainer:
what are the surge pressures on the force main? what are the materials used in its... ...I am trying to understand a sewage pump and force main design.
The total pipe required... ... the high point the flow will run by gravity even though it will be just the same force main .
Could you... ...Hello all. Our client has a 10-inch force main that appears to have too much friction... ... into another 12-inch diameter force main. I haven't seen the as-built drawings yet, but I'd be surprised... SEARCH AGAIN
|
Resources
What is rapid injection molding? For engineers working with tight product design timelines, rapid injection molding can be a critical tool for prototyping and testing functional models. Download NowThe world has changed considerably since the 1980s, when CAD first started displacing drafting tables. Download NowPrototyping has always been a critical part of product development. Download NowAs the cloud is increasingly adopted for product development, questions remain as to just how cloud software tools compare to on-premise solutions. Download Now
|
|
